pc27001-4700 Teledyne Technologies Incorporated., pc27001-4700 Datasheet - Page 4

• Manufacturer Part Number: pc27001-4700
• Description: 1-10a, 270 Vdc Dc Solid-state Power Controller
• Manufacturer: Teledyne Technologies Incorporated.

© 2002 TELEDYNE RELAYS
Insulation Resistance
Input to Output & Case
Thermal Resistance, Junction to Case
Thermal Resistance, Junction to Ambient
STATUS SPECIFICATION
Status Output High I
Status Output Low I
Load Status Turn-On Time
Trip Status Turn-On Time
Load Status Turn-Off Time
Trip Status Turn-Off Time
ENVIRONMENTAL SPECIFICATION
Operating Temperature
Storage Temperature
Constant Acceleration
Seal
NOTES:
• Unless otherwise noted: All tests shall be performed with V
• The transition time for the control signal shall be less than 0.1 msec in application.
• Inductive loads must be diode suppressed. System series inductance in the short circuit mode shall be less than 30 µh.
• Temperature coefficient of transient voltage is 0.25 Volt/C @ Tc = + 25
• Weight
• Package Body Finish:
• Pin Finish:
PC27001-47XX, 65 gm
Nickel Plate Covered by Electroplate gold
Nickel Plate covered by electroplate gold
PC27001-47XX
PC27002-47XX
PC27005-47XX
PC27007.5-47XX
PC27010-47XX
PC27001-47XX
PC27002-47XX
PC27005-47XX
PC27007.5-47XX
PC27010-47XX
OUTPUT (LOAD) SPECIFICATION
sink
source
=4mA
= 4mA
PC27002-47XX, 65 gm
MIL-PRF-28750
MIL-PRF-28750
[phone] • www.teledynerelays.com
Min
Min
Min
-55
-55
10
3.7
8
Typ
Typ
Typ
PC27005-47XX, 70 gm
Max Units
0.25
0.17
0.14
Max Units
0.15 msec
0.15 msec
Max Units
cc
105
125
1.0
0.5
0.4
21
21
19
19
19
= 5.0 V, V
2
2
o
o
o
o
o
o
o
o
o
o
msec
msec
Ohm
Vdc
Vdc
C/W
C/W
C/W
C/W
C/W
C/W
C/W
C/W
C/W
C/W
o
o
C
C
line
o
C.
= Rated Voltage, I
SSPC FUNCTIONAL REQUIREMENTS:
• CASE GROUND: In order for the LOAD
• The CONTROL input is CMOS/TTL
• LOAD STATUS output. A CMOS/TTL
• TRIP STATUS output. A CMOS/TTL HIGH
• Overcurrent operation. The device will trip
PC27007.5-47XX, 70 gm
STATUS to function properly, the case
must be connected to the LINE VOLTAGE
RETURN with impedance of 10 ohms
maximum.
Compatible Logic. The device is
commanded ON, OFF and RESET by a
CMOS/TTL signal at the CONTROL pin. A
HIGH signal will turn the device ON. A
LOW signal or an OPEN condition will turn
the device OFF. If the device trips OFF,
the device is reset by cycling the
CONTROL to OFF then ON with a pulse
width of greater than 50 msec.
HIGH at the LOAD STATUS output
indicates that the device is ON and the
output (load) voltage is present. A CMOS/
TTL LOW at the LOAD STATUS output
indicates that the device is OFF and the
output (load) voltage is not present.
at the TRIP STATUS output indicates that
the device has tripped due to an
overcurrent condition. TRIP STATUS
output is a CMOS/TTL LOW during normal
operation. A TRIP STATUS will change to
CMOS/TTL HIGH in response to an
overcurrent trip. TRIP STATUS will remain
HIGH until the overcurrent condition has
cleared and the device is reset.
(i.e., turn off) if the load current exceeds
the requirement of FIGURE 4. Once the
device is tripped, it will remain OFF
indefinitely, until the overcurrent condition
has cleared and the device is reset.
status
Series 270 VDC PC
= ± 4 ma, I
load
PC27010-47XX, 70 gm
= Rated current.
270VDCPC\072002\Q1
270 VDC PC 67