mn101cf67g Panasonic Corporation of North America, mn101cf67g Datasheet

no-image

mn101cf67g

Manufacturer Part Number
mn101cf67g
Description
Microcontrollers 8-bit Single-chip Microcontrollers
Manufacturer
Panasonic Corporation of North America
Datasheet
 Interrupts
 Timer Counter
 Serial interface
 DMA controller
 I/O Pins
 A/D converter
 Special Ports
 ROM Correction
Type
Internal ROM type
ROM (byte)
RAM (byte)
Package (Lead-free)
Minimum Instruction
Execution Time
RESET. Watchdog. External 0 to 5. Timer 0 to 6. Timer 7 (2 systems). Time base. Serial 0 reception. Serial 0 transmission. Serial 1
reception. Serial 1 transmission. Serial 2 to 4. Automatic transfer finish. A/D conversion finish. Key interrupts (8 lines)
8-bit timer × 7
16-bit timer × 1
Time base timer: One-minute count setting
Watchdog timer × 1
Synchronous type/UART (full-duplex) × 2: Serial 0, 1
Synchronous type × 1: Serial 2
Synchronous type/Single-master I
I
Maximum transfer cycles: 255
Starting factor: External request. Various types of interrupt. Software
Transfer mode: 1-byte transfer. Word transfer. Burst transfer
I/O
Input
10-bit × 7 channels (with S/H)
Buzzer output. Remote control carrier output. High-current drive port
Correcting address designation: Up to 3 addresses possible
2
C slave × 1: Serial 4
MN101C67 Series
Timer 0 ..................Square-wave/8-bit PWM output. Event count. Remote control carrier output. Pulse width measurement
Timer 1 ..................Square-wave output. Event count. Synchronous output event
Timer 2 ..................Square-wave/8-bit PWM output. Event count. Synchronous output event. Pulse width measurement
Timer 3 ..................Square-wave output. Event count. Remote control carrier output
Timer 4 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial 1 baud rate timer
Timer 5 ..................Square-wave/8-bit PWM output. Event count. Pulse width measurement. Serial 0 baud rate timer
Timer 6 ..................8-bit freerun timer
Timer 0, 1 can be cascade-connected
Timer 2, 3 can be cascade-connected
Timer 7 ..................Square-wave/16-bit PWM output (cycle/duty continuous variable). Event count. Synchronous output event. Pulse
Serial 4 ...................I
62 : Common use. Specified pull-up resistor available. Input/output selectable (bit unit)
7 : Common use. Specified pull-up resistor available
width measurement. Input capture
2
C high-speed transfer mode. 7-bit/10-bit address setting. General call
2
C × 1: Serial 3
MN101C67D
* The operation guarantee range for flash memory built-in type is 2.7 V to 3.6 V.
64K
6K
Mask ROM
0.119 µs (at 2.5 V to 3.6 V, 8.39 MHz)*
62.5 µs (at 1.8 V to 3.6 V, 32 kHz)*
0.1 µs (at 2.5 V to 3.6 V, 20 MHz)*
0.2 µs (at 2.1 V to 3.6 V, 10 MHz)*
0.5 µs (at 1.8 V to 3.6 V, 4 MHz)*
TQFP080-P-1212D
[Double speed]
MN101C67G
[Standard]
128K
10K
MN101CF67G
FLASH
MAD00036KEM

Related parts for mn101cf67g

mn101cf67g Summary of contents

Page 1

... TQFP080-P-1212D [Standard] 0.1 µs ( MHz)* 0.2 µs ( MHz)* 0.5 µs ( MHz)* 62.5 µs ( kHz)* [Double speed] 0.119 µs (at 2 3.6 V, 8.39 MHz)* * The operation guarantee range for flash memory built-in type is 2 3.6 V. MN101CF67G FLASH 128K 10K MAD00036KEM ...

Page 2

... P85, LED5, D5 P84, LED4, D4 P83, LED3, D3 P82, LED2, D2 P81, LED1, D1 P80, LED0, D0 Note) Pin 9 serves as the VPP pin in the MN101CF67G, and cannot be used as a user pin. MAD00036KEM MN101C67D, MN101C67G, MN101CF67G Condition fosc = 20 MHz (fs = fosc/2). VDD = 3 V fosc = 8.39 MHz (fs = fosc/2). VDD = 32.768 kHz (fs = fx/2). VDD = 32.768 kHz. VDD = ° ...

Page 3

Request for your special attention and precautions in using the technical information and (1) If any of the products or technical information described in this book exported or provided to non-residents, the laws and regulations of the ...

Related keywords