tda3615j-n2 NXP Semiconductors, tda3615j-n2 Datasheet
tda3615j-n2
Related parts for tda3615j-n2
tda3615j-n2 Summary of contents
Page 1
... DATA SHEET TDA3615J Multiple voltage regulator Product specification Supersedes data of 1998 Jun 23 INTEGRATED CIRCUITS 2004 Jan 12 ...
Page 2
... NAME TDA3615J DBS17P 2004 Jan 12 GENERAL DESCRIPTION The TDA3615J is a multiple output voltage regulator with power switches, intended for use in car radios with or without a microprocessor. It contains: One fixed voltage regulator (regulator 1) intended to supply a microprocessor, that also operates during load dump and thermal shutdown ...
Page 3
... REG1 0 300 mA REG2 0 450 mA REG3 0 100 mA REG4 0 150 mA REG5 0 150 mA REG6 I = 0.55 A SW1 t < SW2 I = 0.35 A SW3 = . L 3 Product specification TDA3615J MIN. TYP. MAX. UNIT 11 14 3.5 14 110 250 A 125 A 4.75 5.0 5.25 V 2.7 2.85 3.0 V 4.75 5.0 5.25 V 9.0 9 ...
Page 4
... Schmitt trigger 2 Schmitt trigger 3 Schmitt trigger 4 Schmitt ANTENNA SWITCH trigger 5 MEDIA SWITCH DISPLAY SWITCH SELECTOR TEMPERATURE AND LOAD DUMP PROTECTION TDA3615J Fig.1 Block diagram. 4 Product specification TDA3615J 14 REG1 (5 V/50 mA) 4 RES 7 SW1 11 SW2 12 SW3 10 REG2 REGULATOR 2 13 (FILAMENT) FILADJ 5 REGULATOR 3 ...
Page 5
... RES 16 reset output GND 17 ground 2004 Jan 12 handbook, halfpage DESCRIPTION 5 Product specification TDA3615J EN1 1 EN2 2 EN3 3 REG6 4 5 REG3 REG4 6 SW1 7 8 REG5 V I(ig) 9 TDA3615J 10 REG2 11 SW2 12 SW3 13 FILADJ REG1 14 V bat 15 16 RES 17 GND MGR100 Fig.2 Pin configuration. ...
Page 6
... Note don’t care. 2004 Jan 12 The filament regulator output voltage of the TDA3615J can be adjusted with pin FILADJ. All output pins are fully protected. The regulators are protected against load dump and short-circuit (foldback current protection, except the filament regulator output). ...
Page 7
... CONDITIONS regulators minutes t 50 ms < note 1 bat I(ig 14.4 V; bat I(ig) selector inputs 0,0,0; note 1 V > < 0 Product specification TDA3615J MIN. MAX. UNIT 62 +150 +150 C VALUE UNIT 2 K/W 40 K/W MIN ...
Page 8
... I 100 mA REG4 10. 16.9 V bat 10. 16.9 V bat 100 mA REG4 f = 120 Hz i(p- 0 note 5 REG4 bat V > REG4 R 0.5 ; note Product specification TDA3615J MIN. TYP. MAX. UNIT 4.75 5.0 5.25 V 4.75 5.0 5.25 V 4.75 5 170 ...
Page 9
... note 5 SW2 I = 0.35 A; note 5 SW3 selector inputs 0,0,0 (state 3 in Table 1 REG1 selector inputs 0,0,0 (state 3 in Table 1 REG1 REG1 REG1 9 Product specification TDA3615J MIN. TYP. MAX. UNIT 9.0 9.5 10.0 V 9.0 9 ...
Page 10
... I(ig 14 I(ig 14 100 bat 14 100 bat L selector inputs 1,0,1 (state 8 in Table 1); note 7 selector inputs 1,0,1 (state 8 in Table 1); note and V . bat REGx 10 Product specification TDA3615J MIN. TYP. MAX. UNIT 6.8 7.35 7.9 V 5.5 5.95 6.4 V 1.4 V 7.2 7.6 8.0 V 6.0 6.3 6.8 V 1.3 V 17.5 18.5 19 ...
Page 11
... V O(REG1) 1 5.0 V O(REG3) 1.6 0 250 2004 Jan 12 2.8 V O(REG2) 100 150 200 I REG1 (mA) 9.5 V O(REG4) 1.6 500 750 1000 I REG3 (mA) Fig.3 Typical foldback current protection behaviour. 11 Product specification 0 250 500 750 I REG2 (mA) 0 200 400 600 I REG4 (mA) MGR101 TDA3615J 1000 800 ...
Page 12
... switch 2 output media 11 16 switch 3 output display 17 ground 12 MGR102 Fig.4 Typical application circuit. 12 Product specification TDA3615J L1 0451707 0.1 F 4400 F DRXSF401XT ( DRF3F201XT 47 F (16 V) C11 100 (16 V) C10 ...
Page 13
... Even when only a small MKT capacitor used as output capacitor, regulator 5 will remain stable over all temperatures. handbook, halfpage 10 100 MGR103 13 Product specification maximum ESR 100 ESR ( ) 75 stable region 50 25 0.022 0 Fig.6 Stability curve of regulator 5 (AM). TDA3615J 10 MGR104 ...
Page 14
... Two problems occur first connection a high charge current will flow through C1 to the ground terminal (pin 17) of the TDA3615J and out of the switch output (pin 11). The media and antenna switches are protected to limit this current. ...
Page 15
... 24.0 20.0 12.2 10 2.54 1.27 5.08 23.6 19.6 11.8 REFERENCES JEDEC JEITA 15 non-concave view B: mounting base side 3.4 8.4 2.4 2.1 6 0.6 4.3 3.1 7.0 1.6 1.8 EUROPEAN PROJECTION Product specification TDA3615J SOT243 2.00 0.25 0.03 1.45 ISSUE DATE 99-12-17 03-03-12 ...
Page 16
... If the temperature of the soldering iron bit is less than 300 C it may remain in contact for seconds. If the bit temperature is between 300 and 400 C, contact may seconds. SOLDERING METHOD DIPPING suitable 16 Product specification TDA3615J ). If the stg(max) WAVE suitable (1) suitable not suitable ...
Page 17
... Product specification TDA3615J DEFINITION These products are not Philips Semiconductors ...
Page 18
Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2004 All rights are reserved. Reproduction in whole or in part is prohibited ...