l6391n STMicroelectronics, l6391n Datasheet

no-image

l6391n

Manufacturer Part Number
l6391n
Description
High-voltage High And Low Side Driver
Manufacturer
STMicroelectronics
Datasheet
Features
Applications
Table 1.
December 2010
High voltage rail up to 600 V
dV/dt immunity ± 50 V/nsec in full temperature
range
Driver current capability:
– 290 mA source,
– 430 mA sink
Switching times 75/35 nsec rise/fall with 1 nF
load
3.3 V, 5 V TTL/CMOS inputs with hysteresis
Integrated bootstrap diode
Comparator for fault protections
Smart shut-down function
Adjustable dead-time
Interlocking function
Compact and simplified layout
Bill of material reduction
Effective fault protection
Flexible, easy and fast design
Motor driver for home appliances, factory
automation, industrial drives and fans.
HID ballasts, power supply units.
Order codes
L6391DTR
Device summary
L6391N
L6391D
Doc ID 17892 Rev 1
High-voltage high and low side driver
Package
DIP-14
SO-14
SO-14
Description
The L6391 is a high-voltage device manufactured
with the BCD “OFF-LINE” technology. It is a single
chip half-bridge gate driver for N-channel power
MOSFET or IGBT.
The high side (floating) section is designed to
stand a voltage rail up to 600 V. The logic inputs
are CMOS/TTL compatible down to 3.3 V for easy
interfacing microcontroller/DSP.
An integrated comparator is available for
protections against overcurrent, overtemperature,
etc.
Tape and reel
Packaging
Tube
Tube
L6391
www.st.com
1/21
21

Related parts for l6391n

l6391n Summary of contents

Page 1

... Motor driver for home appliances, factory automation, industrial drives and fans. ■ HID ballasts, power supply units. Table 1. Device summary Order codes L6391N L6391D L6391DTR December 2010 High-voltage high and low side driver Description The L6391 is a high-voltage device manufactured with the BCD “OFF-LINE” technology single chip half-bridge gate driver for N-channel power MOSFET or IGBT ...

Page 2

Contents Contents 1 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...

Page 3

L6391 1 Block diagram Figure 1. Block diagram Doc ID 17892 Rev 1 Block diagram 3/21 ...

Page 4

Pin connection 2 Pin connection Figure 2. Pin connection (top view) Table 2. Pin description Pin n # Pin name 1 2 SD/ LVG HVG 14 BOOT 1. The ...

Page 5

L6391 3 Truth table Table 3. Truth table Note: X: don't care Input LIN HIN Doc ID 17892 Rev 1 Truth table Output LVG ...

Page 6

Electrical data 4 Electrical data 4.1 Absolute maximum ratings Table 4. Absolute maximum rating Symbol V Supply voltage cc V Output voltage out V Bootstrap voltage boot V High side gate output voltage hvg V Low side gate output voltage ...

Page 7

L6391 4.3 Recommended operating conditions Table 6. Recommended operating conditions Symbol Pin (1) V 14- out boot ...

Page 8

Electrical characteristics 5 Electrical characteristics 5.1 AC operation Table 7. AC operation electrical characteristics (V Symbol Pin Parameter High/low side driver turn- propagation delay High/low side driver turn-off t off propagation delay ...

Page 9

L6391 Figure 3. Timing LIN LVG HIN HVG SD LVG/HVG Figure 4. Typical dead time vs. DT resistor value 50 90 90 Doc ...

Page 10

Electrical characteristics 5.2 DC operation Table 8. DC operation electrical characteristics (V Symbol Pin Parameter hysteresis cc_hys turn ON threshold cc_thON turn OFF threshold cc_thOFF cc Undervoltage quiescent I ...

Page 11

L6391 Table 8. DC operation electrical characteristics (V Symbol Pin Parameter Logic inputs V Low logic level voltage High logic level voltage Single input voltage il_S HIN logic “1” input bias ...

Page 12

Waveforms definitions 6 Waveforms definitions Figure 5. Dead time and interlocking waveforms definitions LIN HIN CONTROL SIGNAL EDGES OVERLAPPED: INTERLOCKING + DEAD TIME LVG HVG (HALF-BRIDGE TRI-STATE) LIN CONTROL SIGNALS EDGES HIN SYNCHRONOUS (*): DEAD TIME LVG HVG LIN CONTROL ...

Page 13

L6391 7 Smart shut down function L6391 integrates a comparator committed to the fault sensing function. The comparator input can be connected to an external shunt resistor in order to implement a simple over- current detection function. The output signal ...

Page 14

Smart shut down function In common over-current protection architectures the comparator output is usually connected to the SD input and an RC network is connected to this SD/OD line in order to provide a mono-stable circuit, which implements a protection ...

Page 15

L6391 8 Typical application diagram Figure 7. Application diagram Doc ID 17892 Rev 1 Typical application diagram 15/21 ...

Page 16

Bootstrap driver 9 Bootstrap driver A bootstrap circuitry is needed to supply the high voltage section. This function is normally accomplished by a high voltage fast recovery diode integrated structure replaces the external diode realized by a high ...

Page 17

L6391 The following equation is useful to compute the drop on the bootstrap DMOS: Equation 3 where Q is the gate charge of the external power MOS, R gate bootstrap DMOS and T For example: using a power MOS with ...

Page 18

Package mechanical data 10 Package mechanical data In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: ...

Page 19

L6391 Table 11. SO-14 mechanical data Dim Figure 11. Package dimensions mm. Min Typ Max 1.75 0.1 0.2 1.65 0.35 0.46 0.19 0.25 0.5 ...

Page 20

Revision history 11 Revision history Table 12. Document revision history Date 14-Dec-2010 20/21 Revision 1 First release Doc ID 17892 Rev 1 L6391 Changes ...

Page 21

... L6391 Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...

Related keywords