bts560 ETC-unknow, bts560 Datasheet
bts560
Available stocks
Related parts for bts560
bts560 Summary of contents
Page 1
... IS Logic GND 1 ) With additional external diode. 2) Additional external diode required for energized inductive loads (see page 8). Semiconductor Group PROFET ® Target Data Sheet BTS560 Product Summary Overvoltage protection Output clamp Operating voltage On-state resistance Load current (ISO) 1) Short circuit current limitation I Current sense ratio chip on chip technology ...
Page 2
... Output to the load. The pins 1 and 5 must be shorted with each other especially in high current applications! T =-40 ...+150°C: j,start = 13 °C = 150°C const., C see diagrams on page 9 Page 2 Target Data Sheet BTS560 3) connection bb 3) Symbol Values self-limited L V ...
Page 3
... 10 OUT d V /dt ) OUT ) -d V /dt OUT ° 150 ° (Pins 1,5 to Tab > out bb = +150°C j Page 3 Target Data Sheet BTS560 Symbol Values min typ ) thJC 30 -- thJA Symbol Values min typ -- 3 L(ISO) tbd -- L(Max) tbd -- ...
Page 4
... T =+150° d(SC mA increases from less than V bIN OUT inductive load switch off. bb ON(CL) Page 4 Target Data Sheet BTS560 Values min typ 5.0 -- bb(on) -- 3.5 bIN( bIN(ucp bIN( 370 tbd 320 tbd 225 ...
Page 5
... tbd (>=20 17) after negative input I = tbd (>=20 17) after change of load tbd (>=20 =-40° 25...+150°C: j Page 5 Target Data Sheet BTS560 Symbol Values min typ 150 -- 3.7 -- ON(rev tbd 530 ...
Page 6
... H 19) <nominal =low and T j < (see diagram on page 15) IN and can thus be detected via the sense current I L Page 6 Target Data Sheet BTS560 Values min typ -- Remark = ilis IS IS,lim ON(Fold back) ...
Page 7
... V bb Inductive and overvoltage output clamp the voltage IN . Use clamped switch-off without D -15 V typ. via V V ON(CL) Page 7 Target Data Sheet BTS560 Z, nominal ( / ...
Page 8
... IN circuit: above 0. 12V and Page 8 Target Data Sheet BTS560 =0). For higher clamp voltages OUT IN PROFET PROFET IS Zb connected to the OUT IN PROFET IS < OUT , V ...
Page 9
... j,start = 150° [mH] 10000 ON(INV) 1000 100 Load i (t) L OUT Page 9 Target Data Sheet BTS560 · L · ON(CL · I ...
Page 10
... Semiconductor Group BTS 660P 560 22 < V after shutdown. In most cases V ON(SC) (see page 7) or leaving open the current sense output. S Page 10 Target Data Sheet BTS560 = 0 V after shutdown ( V OUT < V (see page 4). No latch bb ON(SC) 1998-Jun-17 OUT ...
Page 11
... ILIS k ilis 35000 33000 31000 29000 max 27000 25000 min 23000 21000 19000 17000 15000 150 200 I [A] L Page 11 Target Data Sheet BTS560 ), ° max typ min 0 50 100 150 ), T = 150 ° max typ min 0 50 100 150 ...
Page 12
... Semiconductor Group Typ. input current bIN I [mA] IN 1.6 1.4 1.2 only for t < t d(SC) 1 0.8 0.6 25°C 0.4 150° static dynamic [V] bb Page 12 Target Data Sheet BTS560 ), bIN = 1998-Jun- [V] bIN ...
Page 13
... I t slc(IS soff(IS) Figure 3a: Short circuit: shut down by short circuit detection, reset Shut down remains latched until next reset via input. Page 13 Target Data Sheet BTS560 IN I L(SCp) t d(SC) V >>0 OUT V =0 OUT 1998-Jun- ...
Page 14
... OUT T J Figure 6a: Undervoltage restart of charge pump, overvoltage clamp V 12 OUT dynamic, short 6 Undervoltage not below V bIN( bIN(u) bIN(ucp) Semiconductor Group ON(CL Page 14 Target Data Sheet BTS560 1998-Jun-17 ...
Page 15
... Life support devices or systems are intended ( implanted in the human body or (b) support and/or maintain and sustain and/or protect human life. If they fail reasonably to assume that the health of the user or other persons may be endangered. Page 15 Target Data Sheet BTS560 within components or assemblies. ...