lm5025bmtcx National Semiconductor Corporation, lm5025bmtcx Datasheet - Page 10

• Manufacturer Part Number: lm5025bmtcx
• Description: Active Clamp Voltage Mode Pwm Controller
• Manufacturer: National Semiconductor Corporation

www.national.com
Detailed Operating Description
The LM5025B is a functional variant of the LM5025 active
clamp PWM controller. The functional differences of the
LM5025B are as follows:
The LM5025B PWM controller contains all of the features
necessary to implement power converters utilizing the Active
Clamp Reset technique. The device can be configured to
control either a P-Channel clamp switch or an N-Channel
clamp switch. With the active clamp technique higher effi-
ciencies and greater power densities can be realized com-
pared to conventional catch winding or RDC clamp / reset
techniques. Two control outputs are provided, the main
power switch control (OUT_A) and the active clamp switch
control (OUT_B). The active clamp output can be configured
for either a guaranteed overlap time (for P-Channel switch
applications) or a guaranteed dead time (for N_Channel
applications). The two internal compound gate drivers paral-
lel both MOS and Bipolar devices, providing superior gate
drive characteristics. This controller is designed for high-
speed operation including an oscillator frequency range up
to 1MHz and total PWM and current sense propagation
delays less than 100ns. The LM5025B includes a high-
voltage start-up regulator that operates over a wide input
range of 13V to 100V. Additional features include: Line Un-
der Voltage Lockout (UVLO), softstart, oscillator UP/DOWN
sync capability, precision reference and thermal shutdown.
High Voltage Start-Up Regulator
The LM5025B contains an internal high voltage start-up
regulator that allows the input pin (V
directly to the line voltage. The regulator output is internally
current limited to 20mA. When power is applied, the regula-
tor is enabled and sources current into an external capacitor
connected to the V
range for the V
voltage on the V
and the internal voltage reference (REF) reaches its regula-
tion point of 5V, the controller outputs are enabled. The
outputs will remain enabled until V
line Under Voltage Lock Out detector indicates that V
of range. In typical applications, an auxiliary transformer
winding is connected through a diode to the V
winding must raise the V
internal start-up regulator. Powering V
winding improves efficiency while reducing the controller
power dissipation.
• The maximum PWM duty cycle is limited to less than
• The CS2 hiccup mode threshold is increased to 0.5V
• The CS2 filter discharge device is disabled
• The V
• The V
• The internal 5kΩ COMP pin pull-up resistor is removed
75% to reduce voltage stress on the power MOSFETs
UVLO is below the threshold of normal operation
input falls below the operating threshold
REF
CC
regulator continues to operate when the line
regulator is switched off when the line UVLO
CC
CC
CC
regulator is 0.1µF to 100µF. When the
pin reaches the regulation point of 7.6V
pin. The recommended capacitance
CC
voltage above 8V to shut off the
CC
falls below 6.2V or the
IN
CC
) to be connected
from an auxiliary
CC
pin. This
IN
is out
10
When the converter auxiliary winding is inactive, external
current draw on the V
dissipated in the start-up regulator does not exceed the
maximum power dissipation of the controller.
An external start-up regulator or other bias rail can be used
instead of the internal start-up regulator by connecting the
V
voltage into the two pins.
Line Under-Voltage Detector
The LM5025B contains a line Under Voltage Lock Out
(UVLO) circuit. An external set-point voltage divider from Vin
to GND, sets the operational range of the converter. The
divider must be designed such that the voltage at the UVLO
pin will be greater than 2.5V when Vin is in the desired
operating range. If the undervoltage threshold is not met,
both outputs and the VREF regulator are disabled. The VCC
regulator is not disabled by UVLO. UVLO hysteresis is ac-
complished with an internal 20uA current source that is
switched on or off into the impedance of the set-point divider.
When the UVLO threshold is exceeded, the current source is
activated to instantly raise the voltage at the UVLO pin.
When the UVLO pin voltage falls below the 2.5V threshold,
the current source is turned off causing the voltage at the
UVLO pin to fall. The UVLO pin can also be used to imple-
ment a remote enable / disable function. Pulling the UVLO
pin below the 2.5V threshold disables the PWM outputs.
PWM Outputs
The relative phase of the main (OUT_A) and active clamp
outputs (OUT_B) can be configured for the specific applica-
tion. For active clamp configurations utilizing a ground refer-
enced P-Channel clamp switch, the two outputs should be in
phase with the active clamp output overlapping the main
output. For active clamp configurations utilizing a high side
N-Channel switch, the active clamp output should be out of
phase with main output and there should be a dead time
between the two gate drive pulses. A distinguishing feature
of the LM5025B is the ability to accurately configure either
dead time (both off) or overlap time (both on) of the gate
driver outputs. The overlap / deadtime magnitude is con-
trolled by the resistor value connected to the TIME pin of the
controller. The opposite end of the resistor can be connected
to either REF for deadtime control or GND for overlap con-
trol. The internal configuration detector senses the connec-
tion and configures the phase relationship of the main and
active clamp outputs. The magnitude of the overlap/dead
time can be calculated as follows:
Overlap Time (ns) = 2.8 x R
Dead Time (ns) = 2.9 x R
R
CC
SET
and the V
in kΩ, Time in ns
IN
pins together and feeding the external bias
CC
line should be limited so the power
SET
SET
+20
- 1.2