ca3252 Intersil Corporation, ca3252 Datasheet

ca3252

Manufacturer Part Number

ca3252

Description

Quad Gated Non-inverting Power Driver

Manufacturer

Intersil Corporation

Datasheet

1.CA3252.pdf (6 pages)

Available stocks

Company

Part Number

Manufacturer

Quantity

Price

Company:

Meier Automation Equipment Co., Limited

Part Number:

ca3252CM

Manufacturer:

Quantity:

20 000

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

ca3252E

Quantity:

1 900

Company:

Bonase Electronics (HK) Co., Limited

Part Number:

ca3252M

Manufacturer:

HARRIS

Quantity:

Company:

Meier Automation Equipment Co., Limited

Part Number:

ca3252M

Manufacturer:

INTERSIL

Quantity:

20 000

Current page: 1 of 6
Download datasheet (62Kb)

March 1998

CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.

http://www.intersil.com or 407-727-9207

Features

• Four 600mA Non-Inverting Power Output Drivers

• 50V and 1A Maximum Rated Power Output Drivers

• V

• Inputs Compatible With TTL or 5V CMOS Logic

• Suitable For Resistive, Lamp or Inductive Loads

• Inductive Clamps on Each Output

• High Dissipation Power-Frame Package

• Operating Temperature Ranges . . . . . . -40

Applications

• Solenoids

• Relays

• Lamps

• Steppers

• Small Motors

• Displays

System Applications

• Automotive

• Appliances

• Industrial Controls

• Robotics

Pinouts

CE(SUS)

CLAMP AB

CLAMP CD

Capability . . . . . . . . . . . . . . . . . . . . . . . . . 35V

OUT A

OUT B

OUT C

OUT D

GND

TOP VIEW

CA3252E

(PDIP)

Intersil Corporation 1999

IN A

IN B

ENABLE

GND

IN C

IN D

C to 105

Quad Gated Non-Inverting Power Driver

Description

The CA3252 is used to interface low-level logic to high cur-

rent loads. Each Power Driver has four inverting switches

consisting of an inverting logic input stage and an inverting

low-side driver output stage. All inputs are 5V TTL/CMOS

logic compatible and have a common Enable input. On-chip

steering diodes are connected from each output (in pairs) to

the CLAMP pins (in pairs) which may be used in conjunction

with external zener diodes to protect the IC against over-volt-

age transients that result from inductive load switching. The

CA3252 may be used in a variety of automotive and indus-

trial control applications to drive relays, solenoids, lamps and

small motors.

To allow for maximum heat transfer from the chip, all ground

pins on the DIP and SOIC packages are directly connected

to the mounting pad of the chip. Integral heat spreading lead

frames directly connect the bond pad and ground leads for

good heat dissipation. In a typical application, the package is

mounted on a copper PC Board. By increasing copper

ground area on the PC Board, more heat is conducted away

from the ground leads. The junction-to-ambient thermal

resistances may be reduced to less than 40

approximately two square inches of copper area.

Ordering Information

CA3252E

CA3252M

NUMBER

PART

CLAMP AB

CLAMP CD

OUT B

OUT C

GND

TEMP. (

-40 to 105

CA3252

TOP VIEW

CA3252M

(SOIC)

16 Ld PDIP

20 Ld SOIC

PACKAGE

File Number

OUT A

IN A

INB

ENABLE

GND

IN C

IN D

OUT D

E16.3

M20.3

PKG. NO.

C/W with

1542.2

Related parts for ca3252

ca3252 Summary of contents

Page 1

... CLAMP pins (in pairs) which may be used in conjunction with external zener diodes to protect the IC against over-volt- age transients that result from inductive load switching. The CA3252 may be used in a variety of automotive and indus- trial control applications to drive relays, solenoids, lamps and o ...

Page 2

... TRUTH TABLE (Each Output) ENABLE IN OUT High Low Don’t Care FIGURE 1. CA3252 QUAD NON-INVERTING POWER DRIVER SHOWN WITH TYPICAL APPLICATION LOADS CA3252 GND GND OUT D CLAMP OUT C GND ...

Page 3

... ENABLE GND FIGURE 3. TYPICAL LATCHED ON CIRCUIT SWITCHING CONFIGURATION. WHEN V TURNED ON (LOW). CA3252 V CC CONSTANT CURRENT SOURCE REFERENCE VOLTAGE IN 11k TO SUBSEQUENT STAGES 27k V+ CA3252 3 1.2V V BATT LOAD OUT 0.001 F CLAMP 27V GND IS SWITCHED LOW, THE OUTPUT IS IN ...

Page 4

... Low Enable Voltage Low Enable Current High Enable Voltage High Enable Current CA3252 Thermal Information Thermal Resistance (Typical, Note 2) DC CA3252E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CA3252M Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150 DC Maximum Storage Temperature Range . . . . . . . . . .-65 DC Maximum Lead Temperature Soldering (10s Max 300 (SOIC - Lead Tips Only) ...

Page 5

... Dambar protrusions shall not exceed 0.010 inch (0.25mm the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). CA3252 E16.3 (JEDEC MS-001-BB ISSUE D) 16 LEAD DUAL-IN-LINE PLASTIC PACKAGE SYMBOL ...

Page 6

... For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Sales Ofﬁce Headquarters NORTH AMERICA Intersil Corporation P. O. Box 883, Mail Stop 53-204 Melbourne, FL 32902 TEL: (407) 724-7000 FAX: (407) 724-7240 CA3252 M20.3 (JEDEC MS-013-AC ISSUE C) 20 LEAD WIDE BODY SMALL OUTLINE PLASTIC PACKAGE SYMBOL ...

Related keywords

ca3252 datasheet
ca3252 data sheet
ca3252 pdf datasheet
ca3252 component
ca3252 part
ca3252 distributor
ca3252 RoHS
ca3252 datasheet download