ca3262a Intersil Corporation, ca3262a Datasheet
ca3262a
Available stocks
Related parts for ca3262a
ca3262a Summary of contents
Page 1
... Output Drivers Capable of Switching 700mA Load • Inputs Compatible With TTL or 5V CMOS Logic • Suitable For Resistive, Lamp or Inductive Loads • Power-Frame Package Construction For Good Heat Dissipation • Operating Temperature Ranges - CA3262A . . . . . . . . . . . . . . . . . . . . . . . -40 - CA3262 . . . . . . . . . . . . . . . . . . . . . . . . . -40 Applications System Applications • Solenoids • Automotive • ...
Page 2
... INPUTS FIGURE 2. QUAD INVERTING POWER DRIVER (QDR) SHOWN WITH TYPICAL APPLICATION LOADS CA3262A, CA3262 CONSTANT OUT D CURRENT SOURCES CLAMP OUT C INPUT OUT B ENABLE CLAMP FIGURE 1. CA3262A EQUIVALENT SCHEMATIC OF ONE INPUT STAGE OUT A OUT LIM I LIM T LIM I LIM ...
Page 3
... Thermal Information Thermal Resistance (Typical, Note 3) For PC Mount Without Added Copper Ground Area CA3262E (PDIP CA3262AE (PDIP CA3262AQ (PLCC CA3262AM (SOIC For PC Mount With 2 sq. in. of Added Copper Ground Area CA3262E (PDIP ...
Page 4
... The total DC current for the CA3262 and CA3262A with all 4 outputs ON should not exceed the total 0.7A + Max current will significantly increase the chip temperature due to increased dissipation and may cause thermal shutdown in high ambient tem- perature conditions (See Absolute Maximum Ratings for Dissipation) ...
Page 5
... PHL V OUT (ON) (2) (4) (12) (14 PLH 0 -40 - AMBIENT TEMPERATURE ( FIGURE 4C. TYPICAL PROPAGATION DELAY TIME CHARAC- TERISTICS FIGURE 4. TYPICAL CHARACTERISTICS OF THE CA3262E CA3262A, CA3262 I B CURRENT AMPLIFIER BANDGAP VOLT. REF. CURRENT SENSE SUPPLY VOLTAGE (V 0.7 0.6 0 250mA (EACH) 0.4 0.3 0.2 0.1 -40 ...
Page 6
... AMBIENT TEMPERATURE ( FIGURE 5C. TYPICAL PROPAGATION DELAY TIME CHARACTERISTICS FIGURE 5. TYPICAL CHARACTERISTICS OF THE CA3262AE AND CA3262AQ 2 1.5 1 PACKAGE DERATING WITHOUT HEAT SINK 0 CA3262AQ (PLCC CA3262AE (PDIP), CA3262AM (SOIC AMBIENT TEMPERATURE ( FIGURE 6A. DISSIPATION RATING CHART FOR PLCC, PDIP ...
Page 7
... Dambar protrusions shall not exceed 0.010 inch (0.25mm the maximum number of terminal positions. 10. Corner leads (1, N, N/2 and N for E8.3, E16.3, E18.3, E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch (0.76 - 1.14mm). CA3262A, CA3262 E16.3 (JEDEC MS-001-BB ISSUE D) 16 LEAD DUAL-IN-LINE PLASTIC PACKAGE SYMBOL ...
Page 8
... To be measured at seating plane 5. Centerline to be determined where center leads exit plastic body. 6. “N” is the number of terminal positions. CA3262A, CA3262 N28.45 (JEDEC MS-018AB ISSUE A) 0.004 (0.10 LEAD PLASTIC LEADED CHIP CARRIER PACKAGE ...
Page 9
... However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com CA3262A, CA3262 M24.3 (JEDEC MS-013-AD ISSUE C) ...