mc44144 Freescale Semiconductor, Inc, mc44144 Datasheet - Page 3

• Manufacturer Part Number: mc44144
• Description: Subcarrier Phase-locked Loop
• Manufacturer: Freescale Semiconductor, Inc

function in a video system. When provided NTSC/PAL
composite video or composite chroma and burst gate inputs,
the IC will phase–lock a Voltage Controlled Crystal Oscillator
(VCXO) to the color burst. Both 4X and 1X subcarrier
frequency outputs are provided by the IC. The VCXO
operates off of a 4X subcarrier crystal and The VCXO
operates off a 4X subcarrier crystal and is capable of at least
is a resultant “soft” lock, or a 3 phase shift per 100 Hz
change in oscillator free–run or input reference frequency.
phase detector, the Burst Gate input also initiates a clamp
pulse that sets up the level of the composite video at the input
to the Phase Detector. The start and duration of the Gate
Pulse should be timed so that the pulse envelopes the color
burst of the video signal, but not so wide as to gate sync or
video into the Phase Detector.
Burst Gate input (Pin 7) is above the nominal 2.2 V threshold.
While this makes possible the ability to lock to a color burst,
it does not exclude the possibility of lock to a constant
reference. If a constant source is to be the reference, the
Phase Detector can be permanently enabled by holding the
voltage on the Phase Detector input pin higher than the
threshold voltage.
a constant reference and for a burst–locked application. The
gain in a constant reference application is specified by the
maximum current output with the maximum phase error. For
MOTOROLA ANALOG IC DEVICE DATA
600 Hz of pull–in. The tradeoff for such a wide pull–in range
The MC44144 is designed to implement the color sync
In addition to providing the gate pulse for the MC44144
The Phase Detector is enabled when the voltage at the
The phase detector gain must be specified in two ways, for
1.0k
Reference
Subcarrier
Voltage
Subcarrier
Reference
Output
2.6V
Output
+ 5.0
8
1
1.0n
Divide by 4
Figure 2. Representative Schematic Diagram
Video Clamp
Gate Pulse
Clamp Out
FUNCTIONAL DESCRIPTION
Burst
Gate
7
2
MC44144
470p
75
Composite
a maximum phase error of /2 radians the maximum current
available is approximately 200 A. So the phase detector
gain is defined as,
active for only the duration of the color burst. Therefore the
phase detector gain must be specified as an average gain
over a line period. In this case the phase detector gain for
NTSC and for PAL applications is,
the test schematic Figure 2. This same filter also works for
both NTSC and PAL applications.
(VCXO) uses a design that enables the use of series or
parallel resonant types of crystals. Still, layout and crystal
positioning are critical as the oscillator frequency is sensitive
to shunt capacitance. Care should be taken to keep the
crystal close to the IC and crystal switching should be
avoided. A suitable parallel type crystal would meet the
specifications in Table 1.
this plot the gain must be estimated from the operating point.
KO PAL is the gain for PAL applications and KO NTSC is the
gain for NTSC applications.
Video
6
3
For a burst–locked application, the Phase Detector is
A suitable filter for both types of applications is shown in
The 4X subcarrier Voltage Controlled Crystal Oscillator
A plot showing the VCXO gain is shown in Figure 1. From
0.1
47k
Video In
Clamp In
Reference
Subcarrier
Phase Det Out
0.1
Voltage
Control
Input
4X Ref
Drive
KPD NTSC = (8/( /2))( A/rad
KPD PAL = (7/( /2))( A/rad
VCO
KPD = 200/( /2)( A/rad
1.0k
Detector
Subcarrier
Phase
Output
Crystal
4X Ref
4X
5
4
Out
1.0n
14.32/
17.73MHz
5.0 to 25p
S
S
sec) and,
S
sec)
sec)
3