adc1613d NXP Semiconductors, adc1613d Datasheet - Page 32

• Manufacturer Part Number: adc1613d
• Description: Dual 16-bit Adc; 65 Msps, 80 Msps, 105 Msps Or 125 Msps; Serial Jesd204a Interface
• Manufacturer: NXP Semiconductors

NXP Semiconductors
Table 28.
[1]
[2]
Table 29.
ADC1613D_SER_2
Preliminary data sheet
Bit
7 to 4 -
3 to 0 CFG_SETUP[3:0]
Bit
7
6
5
4
3
The default value for this register depends on the external pull-up/pull-down on CFG0, CFG1, CFG2 or CFG3. Writing to the register
overwrites this value.
F: number of byte per frame; HD: High density; K: number of frames per multi frame; M: number of converters; L: number of lanes
Symbol
Symbol
-
TRISTATE_CFG_PAD
SYNC_POL
SYNC_SINGLE_ENDED R/W
-
SER cfg set-up (address 0803h)
SER control1 (address 0805h)
See the information about the JESD204A standard on the JEDEC web site.
Access
R
R/W
R/W
R/W
Access
R
R
Value
0000
0000
(reset)
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001 to
1101
1110
1111
All information provided in this document is subject to legal disclaimers.
[1]
Value
0
1
0
1
0
1
1
Rev. 02 — 23 April 2010
Description
not used
defines quick JESD204A configuration. These settings overrule the
CFG_PAD configuration
ADC0: ON; ADC1: ON; Lane0: ON; Lane1: ON; F = 2; HD = 0; K = 9;
M = 2; L = 2
ADC0: ON; ADC1: ON; Lane0: ON; Lane1: OFF; F = 4; HD = 0; K = 5;
M = 2; L = 1
ADC0: ON; ADC1: ON; Lane0: OFF; Lane1: ON; F = 4; HD = 0; K = 5;
M = 2; L = 1 SWAP_LANE_1_2 = 1
ADC0: ON; ADC1: OFF; Lane0: ON; Lane1: ON; F = 1; HD = 1;
K = 17; M = 1; L = 2
ADC0: OFF; ADC1: ON; Lane0: ON; Lane1: ON; F = 1; HD = 1;
K = 17; M = 1; L = 2; SWAP_ADC_0_1 = 1
ADC0: ON; ADC1: OFF; Lane0: ON; Lane1: OFF; F = 2; HD = 0; K = 9;
M = 1; L = 1
ADC0: ON; ADC1: OFF; Lane0: OFF; Lane1: ON; F = 2; HD = 0; K = 9;
M = 1; L = 1; SWAP_LANE_1_2 = 1
ADC0: OFF; ADC1: ON; Lane0: ON; Lane1: OFF; F = 2; HD = 0; K = 9;
M = 1; L = 1; SWAP_ADC_0_1 = 1
ADC0: OFF; ADC1: ON; Lane0: OFF; Lane1: ON; F = 2; HD = 0; K = 9;
M = 1; L = 1; SWAP_ADC_0_1
reserved
ADC0: OFF; ADC1: OFF; Lane0: ON; Lane1: ON; F = 2; HD = 0; K = 9;
M = 2; L = 2; loop alignment = 1
ADC0: OFF; ADC1: OFF; Lane0: OFF; Lane1: OFF; F = 2; HD = 0;
K = 9; M = 2; L = 2 → PD
Description
not used
defines the sync signal polarity:
defines the input mode of the sync signal:
not used
CFG pads (3 to 0) are set to high-impedance. Switch to 0
automatically after start-up or reset.
synchronization signal is active low
synchronization signal is active high
synchronization input mode is set in Differential mode
synchronization input mode is set in Single-ended mode
[2]
[2]
[2]
ADC1613D series; serial JESD204A interface
[2]
[2]
ADC1613D series
[2]
[2]
[2]
[2]
[2]
[2]
© NXP B.V. 2010. All rights reserved.
32 of 43