mc145443dw Freescale Semiconductor, Inc, mc145443dw Datasheet - Page 5

• Manufacturer Part Number: mc145443dw
• Description: Single-chip 300-baud Modem
• Manufacturer: Freescale Semiconductor, Inc

RxA2, RxA1
Receive Carrier (Pins 15, 16)
through the receive band–pass filter. RxA1 is the non–invert-
ing input and RxA2 is the inverting input of the receive hybrid
(duplexer) operational amplifier.
LB
Analog Loopback (Pin 2)
the analog loopback test is enabled. The analog loopback
test connects the TxA pin to the RxA2 pin and the RxA1 to
analog ground. In loopback, the demodulator frequencies
are switched to the modulation frequencies for the selected
mode. (See Tables 1 and 2 and Figures 4c and 4d.)
lator generates an echo cancellation tone of 2100 Hz for
MC145442 CCITT V.21 and 2225 Hz for MC145443 Bell 103
systems. For normal operation, this pin should be at a logic
low level (V SS ).
are connected to a logic high level (see Table 2).
MODE
Mode (Pin 13)
used during modulation and demodulation. When a logic
high level is placed on this input, originate (Bell) or channel 1
(CCITT) is selected. When a low level is placed on this input,
answer (Bell) or channel 2 (CCITT) is selected. (See
Tables 1 and 2 and Figure 4.)
CDT
Carrier Detect Timing (Pin 4)
carrier must be present before CD goes low (see Applica-
tions Information for the capacitor values).
CD
Carrier Detect Output (Pin 3)
sensed by the carrier detect circuit. This output goes to a
logic low level when a valid signal above the maximum
threshold level (defined by CDA, Pin 7) is maintained on the
input to the hybrid circuit longer then the response (defined
MOTOROLA
The receive carrier is the FSK input to the demodulator
When a high level is applied to this pin (SQT must be low),
When LB is connected to analog ground (V AG ), the modu-
The power–down mode is enabled when both LB and SQT
This input selects the pair of transmit and frequencies
A capacitor on this pin to V SS sets the amount of time the
This output is used to indicate when a carrier has been
MODE
Pin 13
X
X
X
X
X
1
0
Pin 14
SQT
0
0
0
0
1
1
1
Table 2. Functional Table
V AG (V DD /2)
V AG (V DD /2)
Pin 2
LB
0
0
1
0
1
Originate Mode
Answer Mode
Echo Tone
Analog Loopback
Squelch Mode
Squelch Mode
Power Down
Operating Mode
by CDT, Pin 4). This pin is held at the logic low level until the
signal falls below the maximum threshold level for longer
than the turn off time. (See Applications Information and
Figure 5.)
CDA
Carrier Detect Adjust (Pin 7)
carrier detect threshold. The threshold hysteresis is internally
fixed at 3 dB (see Applications Information ).
X out , X in
Crystal Oscillator (Pins 8, 9)
crystal is connected between these two pins. X out (Pin 8) is
the output of the oscillator circuit, and X in (Pin 9) is the input
to the oscillator circuit. When using an external clock, apply
the clock to the X in (Pin 9) pin and leave X out (Pin 8) open. An
internal 10 M
10 pF on X in and 16 pF on X out , allow the crystal to be con-
nected without any other external components. Printed cir-
cuit board layout should keep external stray capacitance to a
minimum.
FB
Filter Bias (Pin 10)
eration, this pin is connected to analog ground through a
0.1 F bypass capacitor in order to cancel the input offset
voltage of the limiter. It has a nominal input impedance of
16 k . (see Figure 3).
SQT
Transmit Squelch (Pin 14)
disabled. The line driver remains active if LB is at a logic low
level (see Table 2) .
level, see Table 2, the entire chip is in a power down state
and all circuitry except the crystal oscillator is disabled. Total
power supply current decreases from 10 mA (Max) to 300 A
(Max).
BAND–PASS
An external voltage may be applied to this pin to adjust the
A crystal reference oscillator is formed when a 3.579 MHz
This is the negative input to the ac amplifier. In normal op-
When this input pin is at a logic high level, the modulator is
When both LB and SQT are connected to a logic high
FILTER
FROM
10
Figure 3. ac Amplifier Circuit
16 k
FB
0.1 F
resistor and internal capacitors, typically
+
–
490 k
MC145442 MC145443
CARRIER DETECT CIRCUIT
AND DEMODULATOR
TO
5