lt1085ct-pbf Linear Technology Corporation, lt1085ct-pbf Datasheet - Page 9

• Manufacturer Part Number: lt1085ct-pbf
• Description: 7.5a, 5a, 3a Low Dropout Positive Adjustable Regulators
• Manufacturer: Linear Technology Corporation

APPLICATIONS
The problem occurs with a heavy output load when the
input voltage is high and the output voltage is low, such as
immediately after removal of a short. The load line for such
a load may intersect the output current curve at two points.
If this happens, there are two stable output operating
points for the regulator. With this double intersection, the
power supply may need to be cycled down to zero and
brought up again to make the output recover.
Ripple Rejection
The typical curves for ripple rejection reflect values for a
bypassed adjustment pin. This curve will be true for all
values of output voltage. For proper bypassing and ripple
rejection approaching the values shown, the impedance of
the adjust pin capacitor at the ripple frequency should be
less than the value of R1, (normally 100Ω to 120Ω). The
size of the required adjust pin capacitor is a function of the
input ripple frequency. At 120Hz the adjust pin capacitor
should be 25μF if R1 = 100Ω. At 10kHz only 0.22μF is
needed.
For circuits without an adjust pin bypass capacitor, the
ripple rejection will be a function of output voltage. The
output ripple will increase directly as a ratio of the output
voltage to the reference voltage (V
with the output voltage equal to 5V and no adjust pin
capacitor, the output ripple will be higher by the ratio of 5V/
1.25V or four times larger. Ripple rejection will be de-
graded by 12dB from the value shown on the typical curve.
Output Voltage
The LT1083 develops a 1.25V reference voltage between
the output and the adjust terminal (see Figure 1). By
placing a resistor R1 between these two terminals, a
constant current is caused to flow through R1 and down
through R2 to set the overall output voltage. Normally this
current is the specified minimum load current of 10mA.
Because I
with the current through R1, it represents a small error and
can usually be ignored.
ADJ
is very small and constant when compared
U
INFORMATION
U
OUT
W
/V
REF
). For example,
U
Load Regulation
Because the LT1083 is a three-terminal device, it is not
possible to provide true remote load sensing. Load regu-
lation will be limited by the resistance of the wire connect-
ing the regulator to the load. The data sheet specification
for load regulation is measured at the bottom of the
package. Negative side sensing is a true Kelvin connec-
tion, with the bottom of the output divider returned to the
negative side of the load. Although it may not be immedi-
ately obvious, best load regulation is obtained when the
top of the resistor divider R1 is connected directly to the
case not to the load . This is illustrated in Figure 2. If R1
were connected to the load, the effective resistance be-
tween the regulator and the load would be:
R
P
×
V
Figure 2. Connections for Best Load Regulation
IN
⎛
⎜
⎝
*CONNECT R1 TO CASE
V
CONNECT R2 TO LOAD
IN
R
2
R
Figure 1. Basic Adjustable Regulator
+
IN
V
1
OUT
R
LT1083/LT1084/LT1085
1
IN
= V
⎞
⎟
⎠
LT1083
,
50μA
REF
ADJ
I
ADJ
R
( )
P
LT1083
1 +
ADJ
=
R2
R1
OUT
Parasitic Line
+ I
OUT
LINE RESISTANCE
ADJ
PARASITIC
R2
R2*
R1*
V
R
REF
P
R2
R1
Resistance
1083/4/5 ADJ F02
1083/4/5 ADJ F01
V
OUT
R
L
108345ff
9