RR2-S03/D03
3 Watt 2:1 regulated
single & dual output
The models listed are just for standard type. If you need a
special specification product, please contact our service.
Phone: +49 69 984047-0, mail to: info@rsg-electronic.de
or use the forms on www.rsg-electronic.de („Kontakt“).
OUTPUT SPECIFICATIONS
Voltage accuracy
Line regulation
Load regulation
Ripple & Noise
Short circuit protection
Temperature coefficient
Capacitor load
INPUT SPECIFICATIONS
Voltage range
Max. input current
No-load input current
Input filter
Input reflected ripple current
GENERAL SPECIFICATIONS
Efficiency (typ.)
I/O isolation voltage
Metal case / input & output
I/O isolation capacitance
I/O isolation resistance
Switching frequency
Humidity
Reliability calculated MTBF
Safety standard
PHYSICAL SPECIFICATIONS
Case material
Base material
Pin material
Potting material
Weight
Dimensions
ENVIRONMENT SPECIFICATIONS
Operating temperature
Maximum case temperature
Storage temperature
Cooling
Input / Output
(20 MHz bandwith) (1)
(2)
(designed to meet)
(3 sec.)
(See derating curve)
(MIL-HDBK-217F)
(3)
Ø 0.5 mm brass solder-coated
Non-conductive black plastic
(UL94V-0 rated)
Nickel-coated copper
Non-conductive black plastic
(UL94V-0 rated)
Plastic 12.5 g, Metal 15 g
Epoxy (UL94V-0 rated)
1.25“ x 0.8“ x 0.4“
1500 ~ 3500 VDC
Nature convection
> 2.199 Mhrs.
100~400 kHz
60 mV pk-pk
35 mA pk-pk
1000 M Ohm
IEC 60950-1
-40°C~125°C
± 0.02%/°C
-40°C~ 85°C
Continuous
95% rel. H
1000 VDC
60 pF typ.
See table
See table
See table
See table
See table
± 1%
± 0.5%
± 0.5%
PI Type
100°C
■
■
■
■
■
■
■
EMC SPECIFICATIONS
Radiated emissions
Conducted emissions
ESD
RS
EFT
Surge
CS
PFMF
ABSOLUTE MAXIMUM RATINGS
These are stress ratings. Exposure of devices to any of these
conditions may adversely affect long-term reliability.
Input voltage (100 mS)
Lead soldering temperature
All specifications typical at Ta = 25°C, nominal input voltage and full load
unless otherwise specified.
The information and specifications contained in this data sheet are believed
to be correct at time of publication. However, we accept no responsibility
for consequences arising from printing errors or inaccuracies.
Subject to change without notice.
NOTE
1) Typical value at nominal input voltage and full load.
2) Tested by nominal Vin and constant resistor load.
3) Measured input reflected ripple current with a simulated
source inductance of 12uH.
4) Exceeding the absolute ratings of the unit could cause
damage. It is not allowed for continuous operating.
5) Operation under no-load conditions will not damage
these devices. However they may not meet all listed
specifications.
6) It´s necessary to add a minimum capacitor in output for
some models. Please check single model datasheet for
detail value.
7) Input filter components are required to help meet
conducted emission class A, which application refer to the
EMI filter of design & feature configuration.
8) An external filter capacitor is required if the module has
to meet EN 61000-4-4 and EN61000-4-5. The filter
capacitor we suggest: Nippon-chemi-con KY series, 220 uF
/ 100V.
DIL 24, Wide 2:1 input range
Full SMD technology
1500 VDC isolation up to 3500 VDC isolation
Continuous short circuit protection
Efficiency up to 80%
-25°C~85°C operation temperature range
Optional metal case
(8)
(8)
12 modes
24 modes
48 modes
(1.5 mm from case 10 sec.)
5 modes
EN55022
EN55022
IEC61000-4-2 Perf. Crit. B
IEC61000-4-3 Perf. Crit. A
IEC61000-4-4 Perf. Crit. B
IEC61000-4-5 Perf. Crit. B
IEC61000-4-6 Perf. Crit. A
IEC61000-4-8 Perf. Crit. A
-0.7 ~ 15 VDC
-0.7 ~ 24 VDC
-0.7 ~ 40 VDC
-0.7 ~ 80 VDC
260°C
Page: 1/3
Last update: 21.07.09
(4)
Class A
Class A