tk5561a ATMEL Corporation, tk5561a Datasheet
tk5561a
Available stocks
Related parts for tk5561a
tk5561a Summary of contents
Page 1
... Any attempt to fake the base station with a wrong transponder will be recognized immediately. For authentication, the base station transmits a challenge to the TK5561A-PP. This challenge is encrypted by both the IC and the base station. Both should possess the same secret key. Only then can the results be expected to be equal ...
Page 2
... OP-code detect EEPROM control read/write control TESTLOGIC Test Pads VSS Please consider restriction in using the “Adapt”-feature described in the e5561 datasheet. Transponder TK5561A-PP (e5561A + coil + C in plastic cube) C e5561A CRYPTO CIRCUIT MEMORY (320 bit EEPROM) crypto key 64 or 128 bit ID code ...
Page 3
... TK5561A-PP is powered. Writing is carried out by means of Atmel's patented writing method. To transmit data to the TK5561A-PP the read/write base station has to interrupt the RF field for a short time to create a field gap. The information is encoded in the number of clock cycles between two subsequent gaps. ...
Page 4
... Magnetic Field Strength (H) Maximum field strength where transponder does not modulate Minimum Field Strength (H) Read mode Programming mode Lowest adapt frequency Highest adapt frequency Data retention EEPROM Programming cycles EEPROM Programming time/block Maximum field strength TK5561A-PP 4 Symbol T amb T stg T ass H pp Test Conditions T = – ...
Page 5
... Figure 6-1. Figure 6-2. 4682D–RFID–09/06 Typical Curve for Degree of Modulation 0.5 0.4 0.3 0.2 0.1 0 Measurement of the Degree of Modulation – -------------------- - V1 + TK5561A- 100 120 (A/ ...
Page 6
... Figure 7-1. REFERENCE COIL ( IN PHASE ) Figure 7-2. REFERENCE COIL TK5561A-PP 6 Figure 7-1 and Figure Testing Application SENSING COILS (IN PHASE) TK5561A-PP FIELD GENERATING COILS (IN PHASE ) FUNCTION GENERATOR Testing Geometry Transponder 22 mm SENSING COIL 5 mm FIELD GENERATING COIL 7-2). A function generator drives the field generating SUBTRACTOR ...
Page 7
... Writing Data into the TK5561A-PP A write sequence of the TK5561A-PP is shown in occurs by interrupting the RF field with short gaps. After the start gap the write opcode (10) is transmitted. The next 32 bits contain the actual data. The last 4 bits denote the destination block address. If the correct number of bits have been received, the actual data is programmed into the specified memory block ...
Page 8
... Actual Device Behavior The TK5561A-PP detects a gap if the voltage across the coils decreases below a peak-to-peak value of about 800 mV. Until then, the clock pulses are counted. The number given for a valid (see ever, there are always more clock pulses being counted than were applied by the base station. ...
Page 9
... V V EXT S V Batt U2270B 22 µ 680 pF MS Input CFE OE 4.7 k Standby Output Gain 1N4148 COIL2 1.2 nF Read/Write circuit 1. COIL1 DGND GND f res e5561A TK5561A-PP 5V 110 I/O I/O OSC I/O I/O I/O OSC Micro- 100 nF controller 125 kHz kHz 9 ...
Page 10
... TK5561A-PP 15. Revision History Please note that the following page numbers referred to in this section refer to the specific revision mentioned, not to this document. Revision No. 4682D-RFID-09/06 4682C-RFID-06/05 4682B-RFID-05/05 TK5561A-PP 10 Package Remarks – Version of e5561 IDIC History Put datasheet in a new template Pb-free logo on page 1 deleted ...
Page 11
... Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © 2006 Atmel Corporation. All rights reserved. Atmel tered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others. Atmel Operations Memory ...