FTM-9412P-F20F Fiberxon, FTM-9412P-F20F Datasheet
FTM-9412P-F20F
Related parts for FTM-9412P-F20F
FTM-9412P-F20F Summary of contents
Page 1
... Compliant with FCC 47 CFR Part 15, Class B Compliant with FDA 21 CFR 1040.10 and 1040.11, Class I Description FTM-9412P-F20F is Optical Network Unit (ONU) for IEEE802.3ah™-2004 1000BASE-PX20 application. The transceiver is the high performance module for 1.25Gbps data link in single fiber by using 1310nm burst mode transmitter and 1490nm continuous mode receiver with 1550nm optical signal rejection ...
Page 2
... The transceivers have been tested according to American and European product safety and electromagnetic compatibility regulations (See Table 1). For further information regarding regulatory certification, please refer TM to Flexon regulatory specification and safety guidelines, or contact with Fiberxon, Inc. America sales office listed at the end of documentation. Table 1 - Regulatory Compliance Feature ...
Page 3
... Note 4: Refer to Timing Parameter Definition in Burst Mode Note 5: Measured with the Bessel-Thompson filter OFF. Note 6: Maximum sensitivity penalty due to transmitter and dispersion effect through 20km of SMF optical Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Preliminary Data Sheet Symbol Min. Typ. ...
Page 4
... Note 4: Supply current excluding receiver output load. Note 5: LVPECL output, AC coupled internally. (See Note 6: SD (See Pin Function Definitions) Note 7: Tested at 1550nm Note 8: Tested at 1650nm Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Preliminary Data Sheet Definitions) Symbol Min. 1480 P SEN ...
Page 5
... TX_BRST TD+ TD- Optical Power Output T BURST_ON Burst On Condition Figure 1 Timing Parameter Definition in Burst Mode Sequence Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Preliminary Data Sheet T EN_DUR ER for CM operation ER and Average Power within 15% CM operation Burst Off Condition Jan.27, 2005 ...
Page 6
... R1=R2=82Ω,R3=R4=130Ω,R5=N.C . Pin Definitions 2×5 SFF planform in Figure 3 below shows the pin information of electrical interface and mounting studs. Functions are described in Table 6 with some accompanying notes. Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Preliminary Data Sheet 0 .1 µ µ µ µ ...
Page 7
... The form factor is 2×5 SFF with pigtail fiber. The pigtail fiber has a length of 613±30mm and 30mm minimum bending radius. The fiber connector type is SC/UPC. The mechanical design diagram is shown in Figure 4. (Dimension in mm) Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Preliminary Data Sheet Description ...
Page 8
... Mode Field Diameter Gladding Diameter Jacket Diameter Bending Radius of Pigtail Fibre Tension Force on Pigtail Fibre Pigtail Fibre Length Optical Return Loss (UPC type)-1310nm Fiberxon Proprietary and Confidential, Do Not Copy or Distribute Preliminary Data Sheet Figure 4 Mechanical Design Diagram Min. Typical 9 125 ...
Page 9
... Ordering Information Part No. 1310nm(TX)/1490nm(RX), Pigtail 2×5 SFF for GE-PON ONU 20km application, FTM-9412P-F20F with 1550nm optical signal rejection, 0°C ~+70°C Note: The pigtail fiber length and connector type definition can be customized Details included in Fiberxon X-PON Transceiver Family Part Number Rules ...
Page 10
... The results obtained in other operating environment may vary. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN ”AS IS” BASIS event will Fiberxon be liable for damages arising directly from any use of the information contained in this document. Contact U.S.A. Headquarter: ...