MT9042C Mitel Networks Corporation, MT9042C Datasheet - Page 3

• Manufacturer Part Number: MT9042C
• Description: Multitrunk System Synchronizer
• Manufacturer: Mitel Networks Corporation

Advance Information
Notes:
1. All inputs are CMOS with either TTL compatible logic levels, CMOS compatible logic levels or Schmitt trigger compatible logic levels
as indicated in the Pin Description.
2. All outputs are CMOS with CMOS compatible logic levels.
3. See DC Electrical Characteristics for static logic threshold values.
4. See AC Electrical Characteristics - Timing Parameter Measurement Voltage Levels for dynamic logic threshold values.
5. Unless otherwise stated, all unused inputs should be connected to logic high or logic low and all unused outputs should be left open
circuit.
Pin Description
Pin #
16
17
19
20
21
22
23
24
25
26
27
28
Name
RSEL
LOS2
LOS1
C16o
MS2
MS1
RST
C8o
GTo
FS2
FS1
GTi
Clock 8.192MHz (CMOS Output). This output is used for ST-BUS operation at 8.192Mb/s.
Clock 16.384MHz (CMOS Output). This output is used for ST-BUS operation at 16.384Mb/
s.
Guard Time (Schmitt Input). This input is used by the MT9042B state machine in both
Manual and Automatic modes. The signal at this pin affects the state changes between
Primary Holdover Mode and Primary Normal Mode, and Primary Holdover Mode and
Secondary Normal Mode. The logic level at this input is gated in by the rising edge of F8o.
See Tables 4 and 5.
Guard Time (CMOS Output). The LOS1 input is gated by the rising edge of F8o, buffered
and output on GTo. This pin is typically used to drive the GTi input through an RC circuit.
Secondary Reference Loss (TTL Input). This input is normally connected to the loss of
signal (LOS) output signal of a Line Interface Unit (LIU). When high, the SEC reference
signal is lost or invalid. LOS2, along with the LOS1 and GTi inputs control the MT9042B
state machine when operating in Automatic Control. The logic level at this input is gated in
by the rising edge of F8o.
Primary Reference Loss (TTL Input). Typically, external equipment applies a logic high to
this input when the PRI reference signal is lost or invalid. The logic level at this input is gated
in by the rising edge of F8o. See LOS2 description.
Mode/Control Select 2 (TTL Input). This input, in conjunction with MS1, determines the
device’s mode (Automatic or Manual) and state (Normal, Holdover or Freerun) of operation.
The logic level at this input is gated in by the rising edge of F8o. See Table 3.
Mode/Control Select 1 (TTL Input).
edge of F8o. See pin description for MS1.
Reference Source Select (TTL Input). In Manual Control, a logic low selects the PRI
(primary) reference source as the input reference signal and a logic high selects the SEC
(secondary) input. In Automatic Control, this pin must be at logic low. The logic level at this
input is gated in by the rising edge of F8o. See Table 2.
Frequency Select 2 (TTL Input). This input, in conjunction with FS1, selects which of three
possible frequencies (8kHz, 1.544MHz, or 2.048MHz) may be input to the PRI and SEC
inputs. See Table 1.
Frequency Select 1 (TTL Input). See pin description for FS2.
Reset (Schmitt Input). A logic low at this input resets the MT9042B. To ensure proper
operation, the device must be reset after changes to the method of control, reference signal
frequency changes and power-up. The RST pin should be held low for a minimum of 300ns.
While the RST pin is low, all frame and clock outputs are at logic high. Following a reset, the
input reference source and output clocks and frame pulses are phase aligned as shown in
Figure 19.
Description (see notes 1 to 5)
The logic level at this input is gated in by the rising
MT9042C
3