LM2575D2T-12 ON Semiconductor, LM2575D2T-12 Datasheet - Page 8

• Manufacturer Part Number: LM2575D2T-12
• Description: EASY SWITCHERE 1.0 A STEP-DOWN VOLTAGE REGULATOR
• Manufacturer: ON Semiconductor

Buck Converter Basics
the most elementary forward–mode converter. Its basic
schematic can be seen in Figure 15.
time periods. The first one occurs when the series switch is
on, the input voltage is connected to the input of the inductor.
rectifier (or catch diode) is reverse biased. During this period,
since there is a constant voltage source connected across
the inductor, the inductor current begins to linearly ramp
upwards, as described by the following equation:
material in the form of magnetic flux. If the inductor is properly
designed, there is sufficient energy stored to carry the
requirements of the load during the “off” period.
When the power switch turns off, the voltage across the
inductor reverses its polarity and is clamped at one diode
voltage drop below ground by catch dioded. Current now
flows through the catch diode thus maintaining the load
current loop. This removes the stored energy from the
inductor. The inductor current during this time is:
8
The LM2575 is a “Buck” or Step–Down Converter which is
The operation of this regulator topology has two distinct
The output of the inductor is the output voltage, and the
During this “on” period, energy is stored within the core
The next period is the “off” period of the power switch.
Pin
1
2
3
4
5
V in
Switch
Power
Figure 15. Basic Buck Converter
V in
Output
Gnd
Feedback
ON/OFF
I
Symbol
L(on)
+
D1
V
in
– V out t on
This pin is the positive input supply for the LM2575 step–down switching regulator. In order to minimize
voltage transients and to supply the switching currents needed by the regulator, a suitable input bypass
capacitor must be present (C in in Figure 1).
This is the emitter of the internal switch. The saturation voltage V sat of this output switch is typically 1.0 V.
It should be kept in mind that the PCB area connected to this pin should be kept to a minimum in order to
minimize coupling to sensitive circuitry.
Circuit ground pin. See the information about the printed circuit board layout.
This pin senses regulated output voltage to complete the feedback loop. The signal is divided by the
internal resistor divider network R2, R1 and applied to the non–inverting input of the internal error amplifier.
In the Adjustable version of the LM2575 switching regulator this pin is the direct input of the error amplifier
and the resistor network R2, R1 is connected externally to allow programming of the output voltage.
It allows the switching regulator circuit to be shut down using logic level signals, thus dropping the total
input supply current to approximately 80 A. The input threshold voltage is typically 1.4 V. Applying a
voltage above this value (up to +V in ) shuts the regulator off. If the voltage applied to this pin is lower than
1.4 V or if this pin is connected to ground, the regulator will be in the “on” condition.
L
L
C out
PIN FUNCTION DESCRIPTION
DESIGN PROCEDURE
V out
R Load
LM2575
Description (Refer to Figure 1)
turned on. Regulation of the converter is accomplished by
varying the duty cycle of the power switch. It is possible to
describe the duty cycle as follows:
cycle can also be described as:
of the catch diode voltage and the inductor current.
This period ends when the power switch is once again
For the buck converter with ideal components, the duty
Figure 16 shows the buck converter idealized waveforms
d
Figure 16. Buck Converter Idealized Waveforms
+
t on
I min
V D (FWD)
T
Power
Switch
Diode
Off
, where T is the period of switching.
I
MOTOROLA ANALOG IC DEVICE DATA
L(off)
V on(SW)
Switch
Power
Power
Switch
On
+
d
V out – V
+
Power
Switch
Diode
Off
V out
V
I pk
in
L
D
Switch
Power
Switch
Power
On
t
off
I Load (AV)
Time
Time