BTS 3408G Infineon Technologies, BTS 3408G Datasheet
BTS 3408G
Specifications of BTS 3408G
Related parts for BTS 3408G
BTS 3408G Summary of contents
Page 1
Smart Low Side Power Switch Datasheet Rev. 1.3 Features • Logic Level Input • Compatible to 3V micro controllers • ESD protection • Thermal shutdown with auto restart • Overload protection • Short circuit protection • Over voltage protection • ...
Page 2
Product Summary Parameter Supply voltage Continuous drain source voltage On-state resistance Current limitation Nominal output current (individual channel) Clamping energy BTS 3408 FAULT IN1 IN2 ENA Figure 1 Block Diagram Figure 2 Pin Configuration Datasheet Rev. 1.3 Symbol V S ...
Page 3
Pin Definitions and Functions Pin Symbol Function 1 FAULT General Fault Flag; see Table 2 for operation mode. 2 IN1 Input 1; input of channel 1; has an internal pull down; TTL/ CMOS compatible input. 3 IN2 Input 2; input ...
Page 4
Circuit Description Logic Supply The logic is supplied with 4 Volt by the V the logic is shut down and the output stages are switched off. Direct Inputs ENA The ENA/FREEZE input can be used to enable ...
Page 5
Power stages Each output is protected by embedded protection functions. In the event of an overload or short to supply, the current is internally limited. The current limit is set to I operation leads to an overtemperature condition, a second ...
Page 6
Absolute Maximum Ratings T = -40°C to 150°C , unless otherwise specified j Parameter Supply Voltage Drain source voltage (OUT1, OUT2) Input voltage (IN1, IN2, ENA) Continuous input current V FAULT output voltage Operating temperature range Storage temperature range 2) ...
Page 7
Electrical Characteristics 4.5 to 18V; = -40 to 150°C; unless otherwise specified S j Parameter Power supply Supply voltage Supply current in enable mode Supply current in standby mode Power outputs Drain source clamp voltage 2) Output ...
Page 8
Electrical Characteristics (cont’ 4.5 to 18V; = -40 to 150°C; unless otherwise specified S j Parameter Input ’High’ voltage IN1, IN2: ENA: Input voltage hysteresis Input pull down current IN1, IN2: ENA: Digital Output (FAULT) Output ’Low’ ...
Page 9
EMC-Characteristics The following EMC-Characteristics outline the behavior of typical devices. They are not part of any production test. Table 3 Test Conditions Parameter Temperature Supply Voltage Input Voltage (ENA, IN1, IN2) Load Operation mode DUT specific Fast electrical transients acc. ...
Page 10
Figure 3 Test circuit for ISO pulse PULSE V BB stress also for V S 13.5V 3408 VS FAULT OUT1 IN1 IN2 OUT2 ENA GND Datasheet Rev. 1 HITFET BTS3408G 2008-01-09 ...
Page 11
Conducted Emissions Acc. IEC 61967-4 (1Ω/150Ω method) Typ. OUT Emissions at PWM-mode x with 150Ω-matching network 100 -10 -20 0 MHz Figure 4 Test circuit for ...
Page 12
Terms FLT V FLT I IN1 V I IN1 IN2 V I IN2 ENA V ENA Figure 6 Input circuit (ESD protection) ESD zener diodes are not designed for DC current. Figure 7 Inductive and over voltage ...
Page 13
Timing diagrams Figure 9 Switching a resistive load ENA DSx 0.9 Figure 10 Switching an inductive load ENA DSx Figure 11 Short circuit ENA ...
Page 14
Typ. Short Circuit Current D(lim (lim ) typ . Typ. Supply current in ...
Page 15
Datasheet Rev. 1.3 HITFET 15 BTS3408G 2008-01-09 ...
Page 16
Package Outline 1.27 +0.1 2) 0.41 -0. -0.2 Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Lead width can be 0.61 max. in dambar area PG-DSO8-36 ...
Page 17
Revision History Version Date Rev. 1.3 2008-01-09 Changed package outline drawing, updated package name Rev. 1.2 2007-06-15 Released automotive green version Rev. 1.1 2005-10-10 Released production version Datasheet Rev. 1.3 Changes Package parameter (humidity and climatic) removed in Maximum ratings ...
Page 18
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...