IR3086AMTR International Rectifier, IR3086AMTR Datasheet - Page 5

• Manufacturer Part Number: IR3086AMTR
• Description: XPHASE Phase IC with OVP with fault overtemp detect. The IR3086AM Phase IC combined with an IR XPhase TM Control IC provides a full featured and flexible way to implement power solutions for the latest high performance CPUs and ASICs.
• Manufacturer: International Rectifier

Specifications of IR3086AMTR

• Package: 20-Lead MLPQ
• Circuit: X-Phase Phase IC
• Iout (a): 2.5A Gate Driver
• Pbf: PbF Option Available

Note 1: Guaranteed by design, but not tested in production
PIN DESCRIPTION
General
VCC Supply Current
VCCL Supply Current
VCCH Supply Current
BIASIN Bias Current
DACIN Bias Current
Page 5 of 33
PIN#
10
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
6
7
8
9
PIN SYMBOL PIN DESCRIPTION
PARAMETER
PWMRMP
HOTSET
PHSFLT
RMPIN+
ISHARE
SCOMP
RMPIN-
VRHOT
GATEH
GATEL
BIASIN
DACIN
PGND
CSIN+
LGND
VCCH
VCCL
CSIN-
EAIN
VCC
Non-inverting input to Ramp Comparator
Inverting input to Ramp Comparator
Inverting input to VRHOT comparator. Connect resistor divider from VBIAS to LGND
to program VRHOT threshold. Diode or thermistor may be substituted for lower
resistor for enhanced/remote temperature sensing.
Open Collector output of the VRHOT comparator which drives low if IC junction
temperature exceeds the user programmable limit. Connect external pull-up.
Output of the Current Sense Amplifier and input to the Share Adjust Error Amplifier.
Voltage on this pin is equal to V(DACIN) + 34 * [V(CSIN+) – V(CSIN-)]. Connecting
ISHARE pins together creates a Share Bus enabling current sharing between Phase
ICs. The Share bus is also used by the Control IC for voltage positioning and Over-
Current protection.
Compensation for the Current Share control loop. Connect a capacitor to ground to
set the control loop’s bandwidth.
PWM comparator input from the error amplifier of Control IC. Both Gate Driver
outputs drive low if the voltage on this pin is less than 91% of V(DACIN).
PWM comparator ramp input. Connect a resistor from this pin to the converter input
voltage and a capacitor to LGND to program the PWM ramp.
Signal ground and IC substrate connection
Power for internal circuitry
Power for Low-Side Gate Driver
Low-Side Gate Driver Output and input to GATEH non-overlap comparator
Return for Gate Drivers
High-Side Gate Driver Output and input to GATEL non-overlap comparator
Power for High-Side Gate Driver
Non-inverting input to the Current Sense Amplifier
Inverting input to the Current Sense Amplifier and also non-inverting input to the OVP
comparator
Open Collector output of the Phase Fault comparator. Drives low if Phase current is
unable to match the level of the SHARE bus due to an external fault. Connect
external pull-up.
Reference voltage input from the Control IC and inverting input to the OVP
comparator. Current sensing and PWM operation referenced to this pin.
System reference voltage for internal circuitry
6V ≤ V
14V ≤ V
CCH
CCH
≤ 14V
TEST CONDITION
≤ 25V
MIN
-5
-2
IR3086A
TYP
-2.5
-0.5
2.5
5.5
6.5
10
2/13/09
MAX
14
10
5
8
2
1
UNIT
mA
mA
mA
mA
A
A