MAX4733 Maxim, MAX4733 Datasheet
MAX4733
Available stocks
Related parts for MAX4733
MAX4733 Summary of contents
Page 1
... The MAX4731 has two normally open (NO) switches, the MAX4732 has two normally closed (NC) switches, and the MAX4733 has one NO and one NC switch. The MAX4731/MAX4732/MAX4733 are available in 9-bump chip-scale packages (UCSP™), along with 8-pin TDFN ® ...
Page 2
... Hand or wave soldering is not allowed. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS— ...
Page 3
... ELECTRICAL CHARACTERISTICS—Single +3V Supply (continued) (V+ = +3V ±10 +2.0V +0.8V (Notes 3, 4) PARAMETER SYMBOL DYNAMIC CHARACTERISTICS Turn-On Time Turn-Off Time Break-Before-Make (MAX4733 Only, Note 8) Charge Injection On-Channel -3dB Bandwidth Off-Isolation (Note 9) Crosstalk (Note 10) NO_ or NC_ Off-Capacitance COM_ Off-Capacitance C COM_(OFF) COM_ On-Capacitance C COM_(ON) LOGIC INPUT ...
Page 4
... NC_(OFF) COM_ Off-Leakage Current I COM_(OFF) (Note 8) COM_ On-Leakage Current I COM_(ON) (Note 8) DYNAMIC CHARACTERISTICS Turn-On Time Turn-Off Time t Break-Before-Make t (MAX4733 Only, Note 8) Charge Injection On-Channel Bandwidth Off-Isolation (Note _______________________________________________________________________________________ = unless otherwise noted. Typical values are +5V MIN MAX CONDITIONS , ...
Page 5
... Power-Supply Range Positive Supply Current Note 3: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in this data sheet. Note 4: UCSP and TDFN parts are 100% tested at +25°C only, and guaranteed by design over temperature. µMAX parts are 100% tested at +85° ...
Page 6
Dual SPST Analog Switches in UCSP (T = +25°C, unless otherwise noted.) A ON-RESISTANCE vs. V COM +2. +3. +5. +10. ...
Page 7
... Applications Information Operating Considerations for High-Voltage Supply The MAX4731/MAX4732/MAX4733 operate to +11V with some precautions. The absolute maximum rating for V+ is +12V (referenced to GND). When operating near this region, bypass V+ with a minimum 0.1µF capacitor to ground as close to the IC as possible. _______________________________________________________________________________________ ...
Page 8
... Maxim web site at www.maxim-ic.com/ucsp to find the Application Note: UCSP—A Wafer-Level Chip-Scale Package. Test Circuits/Timing Diagrams EXTERNAL BLOCKING DIODE * NO_ * GND EXTERNAL BLOCKING DIODE Figure 1. Overvoltage Protection Using External Blocking Diodes V+ D1 MAX4731 MAX4732 V+ MAX4733 * COM_ * D2 GND *INTERNAL PROTECTION DIODES. ...
Page 9
... Figure 2. Switching Time V+ MAX4733 V+ COM1 NO1 V N_ NC2 COM2 IN1 IN2 LOGIC GND INPUT C INCLUDES FIXTURE AND STRAY CAPACITANCE. L Figure 3. Break-Before-Make Interval (MAX4733 only) MAX4731 MAX4732 MAX4733 R GEN NC_ OR NO_ V GEN GND Figure 4. Charge Injection _______________________________________________________________________________________ Test Circuits/Timing Diagrams (continued) V+ LOGIC V+ INPUT ...
Page 10
... OR V IN_ 2.4V ANALYZER NOTE: DUAL SUPPLIES USED TO ACCOMODATE GROUND-REFERENCED INSTRUMENTS. Figure 6. Crosstalk MAX4731 MAX4732 MAX4733 IN_ TRANSITOR COUNT: 68 PROCESS: CMOS V+ 10nF MAX4731 MAX4732 MAX4733 V+ 50 COM1 NO1/NC1 IN2 IN1 0 OR 2.4V COM2 NO2/NC2 N.C. GND R L 10nF V- Chip Information ...
Page 11
... TDFN EP = EXPOSED PAD MAX4732 NC1 COM1 7 2 IN1 IN2 6 3 COM2 GND 5 4 NC2 MAX MAX4733 IN_ NO1 NC2 0 OFF OFF SWITCHES SHOWN FOR LOGIC "0" INPUT MAX4733 NO1 COM1 IN1 IN2 3 COM2 5 GND 4 NC2 MAX 11 ...
Page 12
... Dual SPST Analog Switches in UCSP (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) 12 ______________________________________________________________________________________ Package Information PACKAGE OUTLINE, 3x3 UCSP 1 21-0093 K 1 ...
Page 13
... Dual SPST Analog Switches in UCSP (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) COMMON DIMENSIONS SYMBOL MIN. A 0.70 D 2.90 E 2.90 A1 0.00 L 0.20 k 0.25 MIN. A2 0.20 REF. -DRAWING NOT TO SCALE- ______________________________________________________________________________________ Package Information (continued) PACKAGE VARIATIONS MAX ...
Page 14
... FRONT VIEW Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 14 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © ...