MAX4607 Maxim, MAX4607 Datasheet
MAX4607
Related parts for MAX4607
MAX4607 Summary of contents
Page 1
... They have low power requirements, require less board space, and are more reliable than mechanical relays. The MAX4607 has two normally closed (NC) switches, the MAX4608 has two normally open (NO) switches, and the MAX4609 has one NC and one NO switch. ...
Page 2
... Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS— ...
Page 3
ELECTRICAL CHARACTERISTICS—Dual Supplies (continued) (V+ = +15V -15V +5V IN_H T = +25°C.) (Note 2) A PARAMETER SYMBOL POWER SUPPLY Power-Supply Range Positive Supply Current Negative Supply Current Logic Supply Current Ground Current SWITCH ...
Page 4
Dual, SPST, CMOS Analog Switches ELECTRICAL CHARACTERISTICS—Single Supply (V+ = +12V +5V IN_H T = +25°C.) (Note 2) A PARAMETER SYMBOL ANALOG SWITCH Input Voltage Range V COM_, (Note 3) ...
Page 5
... Turn-Off Time Charge Injection Crosstalk (Note Capacitance C COM Off-Capacitance C On-Capacitance C Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in this data sheet. Note 3: Guaranteed by design. Note 4: Δ ON(MAX) ON(MIN) Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the specified analog signal range ...
Page 6
Dual, SPST, CMOS Analog Switches (T = +25°C, unless otherwise noted.) A ON-RESISTANCE (DUAL SUPPLY) 4 10mA COM 3.5 V ±5V 3.0 2.5 V ±20V 2.0 V ±15V 1.5 ...
Page 7
... Negative Analog Supply-Voltage Input. Connect to DGND for V- single-supply operation. GND Ground No Connection. Not internally connected. Connect to GND as N.C. low impedance to improve on/off-isolation. V Logic-Supply Input L V+ Positive Analog-Supply Input 2.5 Ω , Dual, SPST, FREQUENCY RESPONSE MAX4607/08/09-11 0 180 ON-RESPONSE -10 190 -20 0 ON-PHASE -90 -30 -40 -180 -270 -50 ...
Page 8
... COM_ Figure 1. Overvoltage Protection Using External Blocking Diodes Test Circuits/Timing Diagrams SWITCH LOGIC OUTPUT NO_ INPUT 100Ω 35pF SWITCH OUTPUT +15V MAX4607 D1 MAX4608 V+ MAX4609 * * NO_ * * V- D2 -15V * INTERNAL PROTECTION DIODES t r < 20ns + < 20ns 50 OFF ...
Page 9
... Figure 5. Crosstalk Test Circuit 2.5 Ω , Dual, SPST, ΔV O OFF OFF ON ON OFF OFF Q = (ΔV )( DEPENDS ON SWITCH CONFIGURATION; IN INPUT POLARITY DETERMINED BY SENSE OF SWITCH. C +15V + COM1 NO1 IN2 IN1 0 or 2.4V COM2 N02 GND -15V MAX4607 MAX4608 MAX4609 50Ω 2.4V N. ...
Page 10
... RoHS status only. Package 16 Narrow SO drawings may show a different suffix character, but the drawing 16 Plastic DIP pertains to the package regardless of RoHS status. 16 Narrow SO PACKAGE TYPE 16 Plastic DIP 16 PDIP 16 SO MAX4607 +15V +5V MAX4608 C MAX4609 COM ...
Page 11
... Flatness parameter in the Electrical Characteristics—Single Supply table. Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...