MAX4361 Maxim, MAX4361 Datasheet

no-image

MAX4361

Manufacturer Part Number
MAX4361
Description
The MAX4361/MAX4362/MAX4363 are a family of high-performance ADSL drivers and drivers/receivers ideal for the upstream transmit path and the downstream receive path of customer premise equipment
Manufacturer
Maxim
Datasheet
The MAX4361/MAX4362/MAX4363 are a family of high-
performance ADSL drivers and drivers/receivers ideal
for the upstream transmit path and the downstream
receive path of customer premise equipment. These
devices operate from a single 5V supply and deliver up
to 12.5dBm average line power for DMT modulated sig-
nals, meeting the requirements of full-rate ADSL.
Spurious-free dynamic range (SFDR) at full output
power is typically -75dBC at 100kHz.
The MAX4361 is a differential IN/differential OUT driver
with a fixed gain of 3.1V/V. The MAX4362 is a dual
amplifier with shutdown intended for use as a differen-
tial IN/differential OUT driver with gain set with external
resistors. The MAX4363 is a quad amplifier with shut-
down intended for use as a differential IN/differential
OUT driver/receiver combination with gain set with
external resistors.
The MAX4361 is offered in a space-saving 8-pin µMAX
package.
19-2299; Rev 0; 1/02
Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd.
For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at
1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.
GND
GND 4
TOP VIEW
IN+
IN- 3
ADSL Drivers/Receivers for Customer Premise
1
2
ADSL Line Interface
HDSL Line Driver
µMAX/SO
MAX4361
________________________________________________________________ Maxim Integrated Products
6
8 OUT+
7 V+
5
General Description
V+
OUT-
T1IN+
SHDN
T2IN+
T1IN-
T2IN-
1
2
3
4
5
Applications
MAX4362
µMAX
10
9
8
7
6
GND
T1OUT
V+
T2OUT
GND
T1IN+
SHDN
T2IN+
T1IN-
T2IN-
N.C.
N.C.
o Low-Noise Driver
o Full-Rate ADSL ATU-R Line Drivers and Receivers
o Single 5V Supply
o -75dBc SFDR at Full Output Power at 100kHz
o -95dB Driver-to-Receiver Crosstalk (MAX4363)
o +12.5dBm Average Line Power (DMT)
o 280mA (min) Peak Output Current
o Rail-to-Rail
o Thermal and Short-Circuit Protection
1
2
3
4
5
6
7
MAX4361EUA
MAX4361ESA
MAX4362EUB
MAX4362ESD
MAX4363EUP
MAX4363ESP
4.8nV/√Hz Voltage-Noise Density
1.5pA/√Hz Current-Noise Density
MAX4362
PART
SO
®
Output Swing
14
13
12
11
10
9
8
GND
N.C.
GND
T1OUT
V+
T2OUT
N.C.
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
-40°C to +85°C
TEMP RANGE
Ordering Information
SHDN
R1IN+
R2IN+
T1IN+
T2IN+
T1IN-
T2IN-
R1IN-
R2IN-
GND
Pin Configurations
10
Equipment
1
2
3
4
5
6
7
8
9
SO/TSSOP
MAX4363
PIN-PACKAGE
8 µMAX
8 SO
10 µMAX
14 SO
20 TSSOP
20 SO
Features
20
19
18
17
16
15
14
13
12
11
GND (TX)
V+ (TX)
T2OUT
GND (TX)
N.C.
V+ (RX)
GND (RX)
R1OUT
R2OUT
T1OUT
1

Related parts for MAX4361

MAX4361 Summary of contents

Page 1

... IN/differential OUT driver with gain set with external resistors. The MAX4363 is a quad amplifier with shut- down intended for use as a differential IN/differential OUT driver/receiver combination with gain set with external resistors. The MAX4361 is offered in a space-saving 8-pin µMAX package. ADSL Line Interface HDSL Line Driver TOP VIEW ...

Page 2

... L SHDN = 5V SHDN = 0 MAX4363, measured at = ∞ V+ (TX), R SHDN = 5V L SHDN = 0 MAX4363, measured at = ∞ V+ (RX), R SHDN = 5V L DMT modulation CAP modulation MAX4361 (0.7V ≤ V ≤ (V+) - 0.7V) OUT MAX4362/MAX4363 (0.7V ≤ V ≤ (V+) - 0.7V) OUT 100kHz 7.1V OUT(DIFF 100kHz 7.1V OUT(DIFF) P-P Inferred from Output Voltage Swing test MAX4361 MAX4362/MAX4363 ...

Page 3

... MAX4362/MAX4363 MAX4361 f = 100kHz AC MAX4362/MAX4363 Inferred from Output Voltage Swing test (V 100Ω (V MAX4362/MAX4363 R = 12.5Ω (V MAX4361 12.5Ω -20°C to 85° MAX4361 MAX4362/MAX4363 SHDN = 0 or SHDN = 1MHz MAX4361 MAX4362/MAX4363 7.1V step OUT(DIFF) P-P ...

Page 4

... Note 2: Implied by worst-case output-voltage swing (V ✕ 10log((250 (V Driver OUT(DIFF) Note 3: Guaranteed by design. Note 4: May exceed absolute maximum ratings for power dissipation if unit is subject to full-scale sinusoids for long periods (see Applications Information section). 4 _______________________________________________________________________________________ = unless otherwise noted. Typical values specified at A ...

Page 5

... FREQUENCY (Hz) Equipment DRIVER DIFFERENTIAL DISTORTION vs. LOAD RESISTANCE - OUT P 100kHz - 12.5Ω L -80 -90 -100 LOAD DRIVER OUTPUT IMPEDANCE vs. FREQUENCY MAX4361 toc05 100 100k 10k SHDN = V 1k 100 0.1 1 0.01 1M 100k 1M FREQUENCY (Hz) DRIVER OUTPUT SWING vs. LOAD RESISTANCE 2.5 2.4 2.3 +SWING 2.2 2.1 2.0 1.9 1 ...

Page 6

... 100Ω 150Ω 100mV P-P -10 10k 100k 1M 10M 100M 1G FREQUENCY (Hz) RECEIVER GAIN AND PHASE vs. FREQUENCY MAX4361 toc12 120 1000 500Ω GAIN -30 -60 10 -90 0 PHASE -120 -10 -20 -150 -30 ...

Page 7

... ADSL Drivers/Receivers for Customer Premise MAX4361 PIN NAME 1, 4 GND 2 IN+ 3 IN- 5 OUT OUT+ MAX4362 PIN NAME µMAX T1IN T1IN SHDN 4 5 T2IN T2IN GND 7 10 T2OUT T1OUT — ...

Page 8

... DMT modulated sig- nals, meeting the requirements of full-rate ADSL. SFDR at full output power is typically -75dBc at 100kHz. Differential In/Differential Out ADSL Driver The MAX4361 is a differential line driver with a fixed gain of 3.1V/V. The gain is set by three internal resistors. 8 _______________________________________________________________________________________ ...

Page 9

... MAX4361/MAX4362/MAX4363 outputs. The MAX4361/MAX4362 require a single 0.1µF bypass from V+ to ground located as close as possible to the IC leads. The MAX4363 features separate supply and ground pins for the receiver and driver amplifiers. Bypass the V+ (RX) supply to the GND (RX) pin with a 0.1µ ...

Page 10

... Hence the average power consumption of the IC is approximately 178mW + quiescent power (110mW), or 288mW. For the MAX4361 in an 8-pin µMAX package, this corre- sponds to a temperature rise of 64°C. With an ambient temperature of +85°C this corresponds to a junction temperature of +148° ...

Page 11

ADSL Drivers/Receivers for Customer Premise 5V 5V 2.7kΩ 0.1µF 2.7kΩ 10kΩ 0.047µF 1kΩ 10kΩ 0.047µF ADSL CHIPSET ______________________________________________________________________________________ Typical Operating Circuit 0.1µF 1kΩ 1kΩ IN1+ OUT+ IN1- DRIVER IN2- OUT- IN2+ 1kΩ MAX4363 1kΩ 5V OUT+ IN1- IN1+ ...

Page 12

ADSL Drivers/Receivers for Customer Premise Equipment 12 ______________________________________________________________________________________ Package Information ...

Page 13

... ADSL Drivers/Receivers for Customer Premise Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 13 © ...

Related keywords