MAX414 Maxim, MAX414 Datasheet
MAX414
Available stocks
Related parts for MAX414
MAX414 Summary of contents
Page 1
... Unity-gain stability, 28MHz bandwidth, and 4.5V/µs slew rate ensure low-noise performance in a wide vari- ety of wideband and measurement applications. The MAX410/MAX412/MAX414 are available in DIP and SO packages in the industry-standard single/dual/quad op amp pin configurations. The single comes in an ultra- small TDFN package (3mm 3mm) ...
Page 2
... Operating Temperature Ranges: MAX41_C_ _ .......................................................0°C to +70°C MAX41_E_ _.....................................................-40°C to +85°C MAX41_M_ _ ..................................................-55°C to +125°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C CONDITIONS MAX410, MAX410B, MAX412, MAX412B V OS MAX414, MAX414B IN(Diff) IN(CM 10Hz ...
Page 3
... V = ±3. VOL R = 600Ω ±3. 2kΩ OUT L I Per amplifier S CONDITIONS MAX410, MAX410B, MAX412, MAX412B V OS MAX414, MAX414B /∆T Over operating temperature range CMRR V = ±3.5V CM PSRR V = ±2.4V to ±5.25V 2kΩ ±3. ...
Page 4
Single/Dual/Quad, 28MHz, Low-Noise, Low-Voltage, Precision Op Amps ELECTRICAL CHARACTERISTICS (MAX410 only) ( -5V -55°C to +125°C, unless otherwise noted.) A PARAMETER SYMBOL Input Offset Voltage ∆V Offset Voltage Tempco Input Bias Current Input Offset ...
Page 5
Single/Dual/Quad, 28MHz, Low-Noise, ( -5V +25°C, unless otherwise noted.) = +25°C, unless otherwise noted VOLTAGE-NOISE DENSITY vs. FREQUENCY 100 = ± +25° 1/F CORNER = ...
Page 6
Single/Dual/Quad, 28MHz, Low-Noise, Low-Voltage, Precision Op Amps ( -5V +25°C, unless otherwise noted.) A SUPPLY CURRENT vs. TEMPERATURE 5 EACH AMPLIFIER = ± -60 - ...
Page 7
... CAPACITANCE LOAD (pF) MAX410-14 toc20 -45 -10 -90 -20 -135 -30 -180 -40 -225 -50 -270 -60 100,000 10,000 MAX412/MAX414 CHANNEL SEPARATION vs. FREQUENCY 150 140 130 120 500Ω 500Ω 110 1kΩ 100 10Ω CHANNEL SEPARATION = 20 log 100 10,000 FREQUENCY (kHz) GAIN AND PHASE vs ...
Page 8
... MAX410/MAX412/ MAX414 negligible. As the source resistance is further increased, current noise becomes dominant. For exam- ple, when the equivalent source resistance is greater than 3kΩ at 1kHz, the current noise component is larg- er than the resistor noise ...
Page 9
... S 2kΩ MAX410 4.7µ 100kΩ MAX410 MAX412 MAX414 0.1µF 24.9kΩ The current-noise density can be calculated, once the value of the input-referred noise is determined, by using the standard expression given below where Inverting input effective series resistance Noninverting input effective series resistance ...
Page 10
... Capacitive Load graph in the Typical Operating Characteristics . Feedback around the isolation resistor RI increases the accuracy at the capacitively loaded output (see Figure 8). The MAX410/MAX412/MAX414 are stable with a 0.01µF load for the values of R decreased closed-loop gain, increase R larger capacitive loads, increase the value of C ...
Page 11
... V- (not the GND plane) for rated power dissipation. Total Supply Voltage Considerations Although the MAX410/MAX412/MAX414 are specified with ±5V power supplies, they are also capable of sin- gle-supply operation with voltages as low as 4.8V. The minimum input voltage range for normal amplifier oper- ation is between ...
Page 12
... SO 8 Plastic DIP 8 Plastic DIP Plastic DIP 14 Plastic DIP Plastic DIP MAX410 TRANSISTOR COUNT: 132 14 Plastic DIP MAX412 TRANSISTOR COUNT: 262 14 SO MAX414 TRANSISTOR COUNT PROCESS: Bipolar PACKAGE CODE P8-1 S8-2 S8-4 T833-2 P14-3 S14 OUT1 OUT4 IN1- ...
Page 13
... Characteristics table for the MAX410. Updated Package Information table. Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...