AD9788 Analog Devices, AD9788 Datasheet - Page 26

no-image

AD9788

Manufacturer Part Number
AD9788
Description
Dual 16-Bit 800 MSPS DAC with Low Power 32-Bit Complex NCO
Manufacturer
Analog Devices
Datasheet

Specifications of AD9788

Resolution (bits)
16bit
Dac Update Rate
800MSPS
Dac Settling Time
n/a
Max Pos Supply (v)
+3.47V
Single-supply
No
Dac Type
Current Out
Dac Input Format
Par

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD9788B5V2
Manufacturer:
ADI
Quantity:
200
Part Number:
AD9788BSV
Manufacturer:
ad
Quantity:
1 831
Part Number:
AD9788BSV
Manufacturer:
ADI
Quantity:
200
Part Number:
AD9788BSVZ
Manufacturer:
AD
Quantity:
490
Part Number:
AD9788BSVZ
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD9788BSVZ
Manufacturer:
XILINX
0
Part Number:
AD9788BSVZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Part Number:
AD9788BSVZRL
Manufacturer:
Analog Devices Inc
Quantity:
10 000
Part Number:
AD9788BSVZRL
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD9788BSVZRL
Quantity:
1 000
Part Number:
AD9788XSVZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
AD9785/AD9787/AD9788
The digital control (DCTL) register comprises two bytes located at Address 0x01.
Table 11. Digital Control (DCTL) Register
Address
0x01
Bit
[15]
[14]
[13]
[12]
[11]
[10]
[9]
[8]
[7:6]
[5]
[4]
[3]
[2]
[1]
[0]
Name
Reserved
Clear phase
accumulator
PN code sync
enable
Sync mode select
Pulse sync enable
Reserved
Inverse sinc
enable
DATACLK
output enable
Interpolation
Factor [1:0]
Data format
Single-port mode
Real mode
IQ select invert
Q first (data
pairing)
Modulator gain
control
Description
Reserved for future use.
0: Default. The feature that clears the NCO phase accumulator is inactive. The phase
accumulator operates as normal.
1: The NCO phase accumulator is held in the reset state until this bit is cleared.
0: PN code synchronization mode is disabled.
1: PN code synchronization mode is enabled. See the Device Synchronization section for
details.
0: Selects pulse mode synchronization.
1: Selects PN code synchronization. See the Device Synchronization section for details.
0: Pulse mode synchronization is disabled.
1: Pulse mode synchronization is enabled. See the Device Synchronization section for details.
Reserved for future use.
0: Default. The inverse sinc filter is bypassed.
1: The inverse sinc filter is enabled and operational.
0: Data clock pin is disabled.
1: Default. The output data clock pin is active (configured as an output).
Specifies the filter interpolation rate where:
0: Default. The incoming data is expected to be twos complement.
1: The incoming data is expected to be offset binary.
0: Default. When the single-port bit is cleared, I/Q data is sampled simultaneously on the P1D
and P2D input ports. Specifically, I data is registered from the P1D[15:0] pins and Q data is
registered from the P2D[15:0] pins.
1: When the single-port bit is set, I/Q data is sampled in a serial word fashion on the P1D input
port. In this mode, the I/Q data is sampled into the part at twice the I/Q sample rate.
0: Default. Logic 0 is the inactive state for this bit.
1: When the real mode bit is set, the Q path logic after modulation and phase compensation is
disabled.
0: Default. When the IQ Select Invert bit is cleared, a Logic 1 on the TXENABLE pin indicates
I data, and a Logic 0 on the TXENABLE pin indicates Q data, if the user is employing a
continuous timing style on the TXENABLE pin.
1: When the IQ Select Invert bit is set, a Logic 1 on the TXENABLE pin indicates Q data, and a
Logic 0 on the TXENABLE pin indicates I data, if the user is employing a continuous timing
style on the TXENABLE pin.
0: Default. When the Q first bit is cleared, the I/Q data pairing is nominal, that is, the I data
precedes the Q data in the assembly of the I/Q data pair. As such, data input to the device as
I0, Q0, I1, Q1 . . . In, Qn is paired as follows: (I0/Q0), (I1/Q1) … (In/Qn).
1: When the Q first bit is set, the I/Q data pairing is altered such that the I data is paired with
the previous Q data. As such, data input to the device as I0, Q0, I1, Q1, I2, Q2, I3, Q3 . . . In, Qn is
paired as follows: (I1/Q0), (I2/Q1), (I3/Q2) … (In + 1/Qn).
0: Default. No gain scaling is applied to the NCO input to the internal digital modulator.
1: Gain scaling of 0.5 is applied to the NCO input to the modulator. This can eliminate
saturation of the modulator output for some combinations of data inputs and NCO signals.
00: 1× interpolation
01: 2× interpolation
10: 4× interpolation
11: 8× interpolation
Rev. A | Page 26 of 64

Related parts for AD9788