ATxmega16D4 Atmel Corporation, ATxmega16D4 Datasheet - Page 272

• Manufacturer Part Number: ATxmega16D4
• Manufacturer: Atmel Corporation

Specifications of ATxmega16D4

• Flash (kbytes): 16 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Speed: No
• Usb Interface: No
• Spi: 4
• Twi (i2c): 2
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 12
• Adc Resolution (bits): 12
• Adc Speed (ksps): 200
• Analog Comparators: 2
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 14
• Input Capture Channels: 14
• Pwm Channels: 14
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

23. Memory Programming
23.1
23.2
8210B–AVR–04/10
Features
Overview
•
•
•
•
•
•
•
This section describes how to program the Non Volatile Memory (NVM) in XMEGA, and covers
both self-programming and external programming. The NVM consist of the Flash Program Mem-
ory, User Signature and Calibration rows, Fuses and Lock Bits, and EEPROM data memory. For
details on the actual memories, how they are organized and the register description for the NVM
Controller used to access the memories, refer to
The NVM can be accessed for read and write both from application software through self-pro-
gramming and from an external programmer. For both external programming and self-
programming access to the NVM is done through the common NVM Controller, and the two
methods of programming are very similar. Memory access is done by loading address and/or
data into the NVM, and a set of commands and triggers that make the NVM Controller perform
specific tasks on the NVM.
From external programming all memory spaces can be read and written, expect for the Calibra-
tion Row which can only be read. The device can be programmed in-system and is accessed
through the PDI using the PDI interface,
detail.
Self-programming and Boot Loader support allows application software in the device to read and
write the Flash, User Signature Row and EEPROM, write the Lock Bits to a more secure setting,
and read the Calibration Row and Fuses. The Flash allows Read-While-Write self-programming
meaning that the CPU can continue to operate and execute code while the Flash is being pro-
grammed.
Read and Write access to all memory spaces from
Self-Programming and Boot Loader Support
External Programming
High Security with Separate Boot Lock Bits for
Reset Fuse to Select Reset Vector address to the start of the
Code Efficient Algorithm
Efficient Read-Modify-Write Support
– External programmers
– Application Software
– Real Read-While-Write Self-Programming
– The CPU can run and execute code while Flash is being programmed
– Any communication interface can be used for program upload/download
– Support for in-system and production programming
– Programming through serial PDI interface
– Fast and reliable interfaces.
– External programming access
– Boot Loader Section access
– Application Section access
– Application Table access
– Application Section, or
– Boot Loader Section
”Self-Programming and Boot Loader Support” on page 276
”External Programming” on page 288
”Memories” on page
18.
describes this in detail.
XMEGA D
describes PDI in
272