TA0102A Tripath Technology Inc., TA0102A Datasheet
TA0102A
Available stocks
Related parts for TA0102A
TA0102A Summary of contents
Page 1
... TA0102A STEREO 150W (4:) CLASS-T DIGITAL AUDIO AMPLIFIER DRIVER USING DIGITAL POWER PROCESSING (DPP TECHNOLOGY ’ ...
Page 2
... UNITS +/- -40 to 150 qC -20 to +80 qC TYP. MAX. UNITS +/- 5 13.2 V TYP. MAX. UNITS 110 160 mA 5 +/- 0.315 0.475 0.70 0. V/V 500 mV TA0102A, Rev. 3.1/06.01 ...
Page 3
... C = 1uF Power Output MOSFET STP19NB20 BBM0 =BBM1 = 1 = 25qC. A TYP. MAX. UNITS 80 W 130 W 100 W 170 W 0.05 % 0. 300 25qC. A TYP. MAX. UNITS 110 W 0.05 % 0.03 % 100 195 0.1uF BY TA0102A, Rev. 3.1/06.01 ...
Page 4
... Not Connected - Must Be Left Floating Tripath Technology, Inc. - Technical Information 28 LO2 27 HO2COM 26 25 HO2 V 24 SNEG V SPOS 23 HO1 22 H01COM 21 LO1 20 19 TA0102A, Rev. 3.1/06.01 ...
Page 5
... SNEG 19 VN12 AGnd PGnd 1 28 Figure 2 V SPOS R S .1uF 100uF SNEG .1uF 100uF V SPOS R S 100uF .1uF SNEG .1uF 100uF TA0102A, Rev. 3.1/06.01 ...
Page 6
... L 22Hz - 22kHz 1kHz BBM = 145nS V = +/-45V 20.75 ST STP19NB20 MOSFET 50 100 150 Output Power (W) Intermodulation Performance +/-45V S 100 200 500 Frequency (Hz) A-Weighted Noise FFT 50 100 200 500 1k 2k Frequency (Hz) TA0102A, Rev. 3.1/06.01 200 250 10k 20k 30k 5k 10k 20k ...
Page 7
... ST STP19NB20 MOSFET 50 75 100 125 150 Output Power (W) Bandwidth 30kHz BW 22kHz BW 50 100 200 500 10k Frequency (Hz) THD+N versus Frequency versus Break Before Make 145nS 105nS 65nS 25nS 50 100 200 500 10k Frequency (Hz) TA0102A, Rev. 3.1/06.01 175 20k 20k ...
Page 8
... THD+N versus Output Power versus Supply Voltage 27V 33.75V 50V 10 100 Output Power (W) Intermodulation Performance 200 500 10k Frequency (Hz 100 200 500 Frequency (Hz) TA0102A, Rev. 3.1/06.01 1000 20k 30k 10k 20k ...
Page 9
... Functional Description TA0102A Amplifier Operation Figure simplified diagram of one channel (channel TA0102A amplifier to assist in understanding its operation. TA0102A 4 MUTE Processing R IN IN1 6 Modulation 7 BBM0 BBM1 OCR1 11 R OCR1 Over/Under Gnd 1 Figure 3. Simplified TA0102A Amplifier The audio input signal (IN1) is fed into the processor internal to the TA0102A, where a modulation pattern is generated ...
Page 10
... The processor portion of the TA0102A is operated from a 5-volt supply (between V5 and AGND). In the generation of the complementary modulation pattern for the output MOSFETs, the processor inserts a “break-before-make” dead time between when it turns one transistor off and it turns the other one on in order to minimize shoot-through currents in the MOSFETs. The dead time can be programmed by setting the break-before-make control bits, BBM0 and BBM1 ...
Page 11
... IN1 and IN2 in the Test/Application Circuit. Nulling should be performed with the inputs shorted to ground. It should be noted that even after nulling, the DC voltage on the output of a TA0102A amplifier with no load in mute mode is approximately 2.5V. This offset does not need to be nulled. The output impedance of the amplifier in mute mode is approximately 10 KOhms ...
Page 12
... Bridged Operation Note that the two channels of a TA0102A amplifier can be used to provide a single, bridged amplifier of almost four times the output power of one of the single-ended amplifier channels. To configure a bridged amplifier, the input to one TA0102A channel must be the inverted signal of the input to the other channel ...