AT93C66A-10SQ-2.7 ATMEL Corporation, AT93C66A-10SQ-2.7 Datasheet
AT93C66A-10SQ-2.7
Available stocks
Related parts for AT93C66A-10SQ-2.7
AT93C66A-10SQ-2.7 Summary of contents
Page 1
... VCC ORG GND Bottom View 3-wire Serial EEPROMs 2K (256 128 x 16) 4K (512 256 x 16) AT93C56A AT93C66A Advance Information 8 VCC ORG 5 GND 8 VCC ORG 5 GND Rev. 3378F–SEEPR–04/04 1 ...
Page 2
Absolute Maximum Ratings* Operating Temperature Storage Temperature Voltage on Any Pin with Respect to Ground Maximum Operating Voltage .......................................... 6.25V DC Output Current........................................................ 5.0 mA Block Diagram 2 The AT93C56A/66A is enabled through the Chip Select pin (CS) and accessed ...
Page 3
Pin Capacitance Applicable over recommended operating range from T Symbol Test Conditions C Output Capacitance (DO) OUT C Input Capacitance (CS, SK, DI) IN Note: 1. This parameter is characterized and is not 100% tested. DC Characteristics Applicable over ...
Page 4
AC Characteristics Applicable over recommended operating range from TTL Gate and 100 pF (unless otherwise noted). Symbol Parameter SK Clock f SK Frequency t SK High Time SKH t SK Low Time SKL Minimum CS t ...
Page 5
... Instruction Set for the AT93C56A and AT93C66A Op Instruction SB Code READ 1 10 EWEN 1 00 11XXXXXXX ERASE 1 11 WRITE 1 01 ERAL 1 00 10XXXXXXX WRAL 1 00 01XXXXXXX EWDS 1 00 00XXXXXXX Note: The X’s in the address field represent don’t care values and must be clocked. ...
Page 6
Timing Diagrams Synchronous Data Timing Note: 1. This is the minimum SK period. 6 WRITE (WRITE): The Write (WRITE) instruction contains the bits of data to be written into the specified memory location. The self-timed programming cycle ...
Page 7
... Notes DON’T CARE value, but the extra clock is required DON’T CARE value, but the extra clock is required. 7 ... AT93C66A (4K ( ...
Page 8
EWDS Timing WRITE Timing HIGH IMPEDANCE DO (1) WRAL Timing HIGH IMPEDANCE O Note: 1. Valid only 4.5V to 5.5V ... 0 0 ...
Page 9
ERASE Timing HIGH IMPEDANCE DO (1) ERAL Timing HIGH IMPEDANCE DO Note: 1. Valid only 4.5V to 5.5V. CC 3378F–SEEPR–04/ ... N-1 ...
Page 10
AT93C56A Ordering Information Ordering Code AT93C56A-10PI-2.7 AT93C56A-10SI-2.7 AT93C56AW-10SI-2.7 AT93C56A-10TI-2.7 AT93C56AU3-10UI-2.7 AT93C56AY1-10YI-2.7 AT93C56A-10PI-1.8 AT93C56A-10SI-1.8 AT93C56AW-10SI-1.8 AT93C56A-10TI-1.8 AT93C56AU3-10UI-1.8 AT93C56AY1-10YI-1.8 AT93C56A-10SU-2.7 AT93C56A-10SU-1.8 AT93C56A-10TU-2.7 AT93C56A-10TU-1.8 AT93C56A-10SQ-2.7 AT93C56A-10SE-2.7 Note: For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in ...
Page 11
... AT93C66A-10TI-1.8 AT93C66AU3-10UI-1.8 AT93C66AY1-10YI-1.8 AT93C66A-10SU-2.7 AT93C66A-10SU-1.8 AT93C66A-10TU-2.7 AT93C66A-10TU-1.8 AT93C66A-10SQ-2.7 AT93C66A-10SE-2.7 Note: For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table. 8P3 8-lead, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8S1 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8S2 8-lead, 0.200" ...
Page 12
Packaging Information 8P3 – PDIP Top View PLCS Side View Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured ...
Page 13
JEDEC SOIC e Side View Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 R 3378F–SEEPR–04/04 1 ...
Page 14
EIAJ SOIC 1 N Top View e D Side View Notes: 1. This drawing is for general information only; refer to EIAJ Drawing EDR-7320 for additional information. 2. Mismatch of the upper and lower dies and resin burrs ...
Page 15
TSSOP Pin 1 indicator this corner N Top View Side View Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, ...
Page 16
PIN 1 BALL PAD CORNER Top View PIN 1 BALL PAD CORNER 1 2 (d1 (e1) Bottom View 8 SOLDER BALLS 1. Dimension 'b' is measured at the maximum solder ball diameter. This ...
Page 17
MAP D E Top View Side View 2325 Orchard Parkway San Jose, CA 95131 R 3378F–SEEPR–04/ End View A SYMBOL TITLE 8Y1, 8-lead (4.90 x 3.00 mm ...
Page 18
... Fax: (81) 3-3523-7581 Disclaimer: Atmel Corporation makes no warranty for the use of its products, other than those expressly contained in the Company’s standard warranty which is detailed in Atmel’s Terms and Conditions located on the Company’s web site. The Company assumes no responsibil ity for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time wit h out notice, and does not make any commitment to update the information contained herein ...
Page 19
Copyright © Each Manufacturing Company. All Datasheets cannot be modified without permission. This datasheet has been download from : www.AllDataSheet.com 100% Free DataSheet Search Site. Fast Search System. www.AllDataSheet.com Free Download. No Register. ...