RF2466 RF Micro Devices, RF2466 Datasheet

no-image

RF2466

Manufacturer Part Number
RF2466
Description
Manufacturer
RF Micro Devices
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
RF2466
Manufacturer:
MITSUMI
Quantity:
2 692
Part Number:
RF2466
Manufacturer:
RF
Quantity:
1 000
Part Number:
RF2466
Manufacturer:
RF
Quantity:
20 000
Part Number:
RF2466TB7
Manufacturer:
TI
Quantity:
28
Part Number:
RF2466TR13
Manufacturer:
ETRO
Quantity:
7 656
Product Description
The RF2466 is a receiver dual downconverter designed
for the receive section of dual-mode CDMA/FM cellular
applications. It is designed to downconvert RF signals
while providing 14dB gain in CDMA mode and 7dB gain
in FM mode. Also, it features IF output selection and
power down mode. Noise Figure, IP3, and other specs
are designed to be compatible with the IS-95 Interim
Standard for CDMA cellular communications. The IC is
manufactured on an advanced Silicon Bipolar process.
ü
Optimum Technology Matching® Applied
Rev A7 010717
Typical Applicat ions
• CDMA/FM Cellular Systems
• Supports Dual-Mode AMPS/CDMA
• Supports Dual-Mode TACS/CDMA
Si BJT
Si Bi-CMOS
Funct ional Block Diagram
GaAs HBT
SiGe HBT
6
GaAs MESFET
Si CMOS
• General Purpose Downconverter
• Commercial and Consumer Systems
• Portable Battery-Powered Equipment
x x
x x
x x
x x
x x
x x
x x
x x
x x
x x
x x
x x
Feat ures
Ordering Infor mat ion
RF Micro Devices, Inc.
7628 Thorndike Road
Greensboro, NC 27409, USA
xxxxxxxxx
x x x
x x x
xxxxxxxxx
x x x
xxxxxxxxx
xxxxxxxxx
xxxxxxxxx
xxxxxxxxx
xxxxxxxxx
xxxxxxxxx
xxxxxxxxx
x x x
x x x
x x x
x x x
x x x
x x x
Dimensions in mm.
• Dual Mode CDMA/AMPS
• Dual Mode JCDMA/TACS
• Digitally Selectable IF Outputs
• 500MHz to 1100MHz Operation
• Power Down Mode
RF2466
RF2466 PCBA
x x
x x
x x
x x
x x
x x
x x
x x
x x
x x x
x x x
x x x
x x x
x x x
x x x
x x x
x x x
x x x
3.75
INDEX AREA 3
Package Style: LCC, 16-Pin, 4x 4
x x
x x
x x
x x
x x
x x
x x
x x
x x
x x x
x x x
x x x
x x x
x x x
x x x
x x x
x x x
x x x
x x
x x
x x
x x
x x
x x
x x
x x
x x
x x
x x
x x
3V CDMA/FM Mixer
Fully Assembled Evaluation Board
0.05
0.00
3.75
12°
0.75
0.65
1.00
0.90
x x
x x
x x
x x
x x
x x
x x
x x
x x
x x
x x
x x
1
3
3V CDMA/FM MIXER
NOTES:
2
4
5
0.75
0.50
Shaded Pin is Lead 1.
Dimension applies to plated terminal and is measured between
0.10 mm and 0.25 mm from terminal tip.
The terminal #1 identifier and terminal numbering convention
shall conform to JESD 95-1 SPP-012. Details of terminal #1
identifier are optional, but must be located within the zone
indicated. The identifier may be either a mold or marked
feature.
Pins 1 and 9 are fused.
Package Warpage: 0.05 max.
RF2466
0.45
0.28
http://www.rfmd.com
1.50 SQ
Fax (336) 664 0454
Tel (336) 664 1233
3.20
4.00
+
2
0.80
TYP
1
1.60
1
4.00
6-7
6

Related parts for RF2466

RF2466 Summary of contents

Page 1

... CDMA/FM Cellular Systems • Supports Dual-Mode AMPS/CDMA • Supports Dual-Mode TACS/CDMA Product Description The RF2466 is a receiver dual downconverter designed for the receive section of dual-mode CDMA/FM cellular applications designed to downconvert RF signals while providing 14dB gain in CDMA mode and 7dB gain in FM mode ...

Page 2

... RF2466 Absolute Maximum Ratings Parameter Supply Voltage Operating Ambient Temperature Storage Temperature Parameter Overall RF Frequency Range LO Frequency Range IF Frequency Range Conversion Gain 6 Noise Figure Input VSWR Input IP3 Input P1dB MIX IN to IF1, IF2 Rejection IF1, IF2 Output Freq. Range Output Impedance ...

Page 3

... Same as pin 15, except complementary output. Rev A7 010717 . CC , sets the operating impedance. This CC at 85MHz. Because this pin is biased sets the blocking capacitor must be used if the IF CC RF2466 Interface Schematic IN+ LO IN- See pin 4. MIX IN VCC2 BIAS LO OUT See pin 13 ...

Page 4

... RF2466 Pin Function Description Pkg GND Ground connection. The backside of the package should be soldered to a top side ground pad which is connected to the ground plane with mul- Base tiple vias. 6 6-10 Interface Schematic Rev A7 010717 ...

Page 5

... IF SELECT 8.2 nH 200 3.3 pF Rev A7 010717 Applicat ion Schemat MIX IN RF2466 CDMA CDMA IF OUT L Saw Filter L FM Saw FM IF OUT Filter 6-11 6 ...

Page 6

... RF2466 + VCC R1 50 strip 33 J3 CDMA IF1 R2 68 VCC IF SEL 6 ENABLE strip 3.0 pF **Core: Fair-Rite Balun #2865002402 L12: 3 turns #30 AWG (Green) L34: 12 turns #32 AWG (Red) One turn = one pass through BOTH holes. Winding starts and finishes on same end of core. ...

Page 7

... Evaluat ion Board Layout Board Size 3.070” x 2.928” Board Thickness 0.056”, Board Material FR-4, Multi-Layer Rev A7 010717 RF2466 6 6-13 ...

Page 8

... RF2466 CDMA Gain and Noise Figure versus LO Drive 14.0 13.0 12.0 11.0 10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0.0 -10.0 -9.0 -8.0 -7.0 -6.0 -5.0 LO Drive (dBm Gain and Noise Figure versus LO Drive 8.0 7.0 6.0 5.0 4.0 3.0 2.0 1.0 0.0 -10.0 -9.0 -8.0 -7.0 -6.0 -5.0 LO Drive (dBm) 6-14 13.0 12.0 12.5 CDMA Gain (dB) 11.0 CDMA NF (dB) 12.0 10.0 11.5 9.0 11.0 10.5 8.0 10.0 7.0 9.5 6.0 9.0 5.0 8.5 8.0 4.0 -4.0 -3.0 -2.0 -1.0 0.0 -10.0 16.0 9.0 8.0 14.0 7.0 FM Gain (dB (dB) 6.0 12.0 5.0 4.0 10.0 3.0 2.0 8.0 1.0 6.0 0.0 -4.0 -3.0 -2.0 -1.0 0.0 -10.0 -9.0 CDMA IIP3 and Noise Figure versus LO Drive CDMA IIP3 (dBm) CDMA NF (dB) -9.0 -8.0 -7.0 -6.0 -5.0 -4.0 -3.0 -2.0 -1.0 LO Drive (dBm) FM IIP3 and Noise Figure ...

Related keywords