SAA6588 Philips Semiconductors, SAA6588 Datasheet
SAA6588
Available stocks
Related parts for SAA6588
SAA6588 Summary of contents
Page 1
... DATA SHEET SAA6588 RDS/RBDS pre-processor Product specification Supersedes data of 1997 Sep 01 File under Integrated Circuits, IC01 INTEGRATED CIRCUITS 2002 Jan 14 ...
Page 2
... RDS/RBDS radio. Moreover the timing requirements of the set controller, regarding RDS/RBDS data processing are reduced due to the integration of decoder functions, so that the development of radio control software can be concentrated specifically on radio set features. 2 Product specification SAA6588 2 C-bus. ...
Page 3
... SAA6588T SO20 plastic small outline package; 20 leads; body width 7.5 mm 2002 Jan 14 CONDITIONS MIN. 4.5 4.5 1 adjustable in 4 steps 20 PACKAGE DESCRIPTION 3 Product specification SAA6588 TYP. MAX. UNIT 5.0 5.5 V 5.0 5 0.6 dB 18.6 dB 161.7 ms 4.332 MHz 8 ...
Page 4
... DETECTOR C11 LVIN 20 level input 2 DDA POWER SUPPLY AND RESET C8 100 SSA V ref C7 2.2 F 560 pF C10 CIN 18 19 CLOCKED RDS/RDBS COMPARATOR DEMODULATOR SAA6588 SIGNAL QUALITY 4 MULTI-PATH DETECTOR DETECTOR 5 4 TEST OSCILLATOR CONTROL AND CLOCK TCON MRO OSCI OSCO 470 100 4.332 ...
Page 5
... MRO 1 20 LVIN MPTH 19 CIN 2 TCON 3 18 SCOUT OSCO 17 V ref 4 OSCI 16 MPX 5 SAA6588T V SSD SSA V DDD V DDA 7 14 DAVN 8 AFIN 13 SDA 9 12 MAD SCL 11 PSWN 10 MGK534 Fig.3 Pin configuration (SO20). ...
Page 6
... Philips Semiconductors RDS/RBDS pre-processor FUNCTIONAL DESCRIPTION General The following functions are performed by the SAA6588: Selection of the RDS/RBDS signal from the MPX input signal 57 kHz carrier regeneration Demodulation of the RDS/RBDS signal Symbol decoding RDS/RBDS block detection Error detection and correction of transmission errors ...
Page 7
... If the decoder is synchronized and detects a bit slip, the synchronization is corrected bit via block detection on the respectively shifted expected new block. 7 Product specification SAA6588 2 C-bus request. 2 C-bus in a range ...
Page 8
... If the pre-processor is synchronized and in any DAV mode loss of synchronization is detected (flywheel counter overflow and resulting restart of synchronization). In any DAV mode reset condition caused by power-on or voltage-drop is detected. 8 Product specification SAA6588 C-bus. After detection of data overflow 2 C-bus. 2 C-bus. ...
Page 9
... The pause detector watches the audio modulation for pauses or very low levels. This function can be used for performing inaudible RDS AF-tests if the radio mode as well as for Automatic Music Search (AMS) if the radio is in cassette mode. 9 Product specification SAA6588 2 C-bus (see Fig.5). This causes a 2 C-bus 2 C-bus ...
Page 10
... C-bus interface requires a defined reset condition. is switched on DDD 2 C-bus interface registers 2 C-bus slave control and releases the data 2 C-bus is used. 2 C-bus interface acts as a slave 2 C-bus interface is connected to the external I Product specification SAA6588 DDA . ref 2 C-bus. This 2 C-bus ...
Page 11
... SYM1 selection of error correction mode for synchronization search; see Table 4 3 SYM0 2 RBDS 0: RDS processing mode 1: RBDS processing mode 1 DAC1 selection of data output protocol and indirectly control of data available output 0 DAC0 signal (DAVN); see Table 5 11 Product specification SAA6588 FUNCTION FUNCTION ) W FUNCTION ...
Page 12
... PFT1 and PFT0 adjustment of signal quality detector sensitivity ( 9 to +9.6 dB); see Table 10 PAUSE LEVEL PL0 (mV RMS Product specification DESCRIPTION DESCRIPTION ) W FUNCTION FUNCTION BELOW DOLBY FM DEVIATION LEVEL (dB) 30.2 26.2 22.2 18.2 SAA6588 ) W (kHz) 1.0 1.6 2.5 4.0 ...
Page 13
... Jan 14 SOSC = 0 PTF0 MINIMUM TIME (ms) 0 20.2 1 40.4 0 80.8 1 161.7 SQS SQS2 SQS1 Product specification SAA6588 SOSC = 1 OSCILLATOR FREQUENCY (MHz) 4.332 ( 8.664 ( 12.996 ( 17.328 ( CORRECTION SQS0 HEX (dB) 9.0 8.4 7.8 7.2 6.6 6.0 5.4 4.8 4.2 3.6 3.0 2.4 1 ...
Page 14
... COMMENTS Table 14 Processed error correction ELB1/ EPB1 Table 15 Bytes 1 BYTE ) FUNCTION Product specification SAA6588 BL1/ BL0/ BLOCK IDENTIFICATION BP1 BP0 0 0 block block block block block C’ block E (RBDS mode invalid block E (RDS mode invalid block ELB0/ MODE DESCRIPTION EPB0 0 ...
Page 15
... Human body model (equivalent to discharging a 100 pF capacitor through a 1.5 k series resistor). Except pin 17: 4000 V minimum and +2500 V maximum. 3. Machine model (equivalent to discharging a 200 pF capacitor through a 0 THERMAL CHARACTERISTICS SYMBOL PARAMETER R thermal resistance from junction to ambient th(j-a) SAA6588T (SOT163-1) SAA6588 (SOT146-1) 2002 Jan 14 CONDITIONS MIN. 0 0.5 note 1 10 ...
Page 16
... V MAD DDD MAD IL1 V = 3.5 V MAD 4.0 mA OL1 I = 6.0 mA OL2 4 +85 C amb f 12.996 MHz osc f = 17.328 MHz osc 16 Product specification SAA6588 TYP. MAX. UNIT 5.0 5 0.3V V DDD +1.5 V +0.3V V DDD 0.5 V DDD 0.4 V 0 4.332 MHz 8.664 MHz 12 ...
Page 17
... +85 C amb kHz kHz f < 45 kHz f < 20 kHz f > 70 kHz kHz kHz kHz kHz kHz C6 = 100 nF 470 k 17 Product specification SAA6588 MIN. TYP. MAX. UNIT 4.5 5.0 5 0.5 V 14.0 mA 2.25 2.5 2. ...
Page 18
... Table 10 100 kHz after acknowledgement of the 2 I C-bus transceiver kHz unloaded PL1 = 1; PL0 = 1 PT1 = 0; PT0 = 0 PT1 = 0; PT0 = 1 PT1 = 1; PT0 = 0 PT1 = 1; PT0 = 1 18 Product specification SAA6588 MIN. TYP. MAX. UNIT 150 200 250 0.5 3 ...
Page 19
... STOP condition. In case of transmission errors during a write cycle, the pre-processor can indirectly stop the transfer by generating no acknowledge (SDA = HIGH) hereafter the master can send the STOP condition. (3) (4) ( DATA and (3) (4) ( DATA (4) (5) (4) (5) DATA A DATA (4) (5) (6) DATA A Product specification SAA6588 (4) ( (7) P ...
Page 20
... Notes 1. See Fig.4a. 2. See Fig.4b. 2002 Jan 14 t DAVL t TDAV t DV pre-processor addressed t DAVL t TDAV C-bus (decoder is synchronized). Fig.4 Data available signal (DAVN). 2.0 21.9 21.9 (1) 10.1 depends on data request via I 20 Product specification SAA6588 MGK540 MGK541 TYP. UNIT (2) C-bus ms ...
Page 21
... DAC1 DAC0 acknowledgement from slave A FEB2 FEB1 FEB0 acknowledgement from slave A P SQS3 SQS2 SQS1 SQS0 STOP condition from master MGK538 acknowledgement from slave A MAD 0 acknowledgement from slave RBDS DAC1 DAC0 A P STOP condition from master MGK539 Product specification SAA6588 ...
Page 22
... M08 A M01 M00 A A PM10 PM09 PM08 A PM03 PM02 PM01 PM00 A BEC2 BEC1 BEC0 EPB1 EPB0 not acknowledged from master byte 6 R from device not BP0 SQI3 SQI2 SQI1 SQI0 used MGK537 Product specification SAA6588 A P STOP condition from master ...
Page 23
... Q1: 4.332 MHz, 8.664 MHz, 12.996 MHz or 17.328 MHz. C18 (1) 470 (1) ( PSWN MAD 12 AFIN DDA 100 nF 470 nF 470 nF V SSA 15 SAA6588 C10 MPX 16 330 pF C11 V ref 17 2.2 F SCOUT 18 C12 560 pF CIN 19 C13 LVIN C-bus interface. Fig.8 Application diagram (1) (1) 270 470 (3) R6 ...
Page 24
... REFERENCES JEDEC EIAJ MS-001 SC-603 24 Product specification 3.60 8.25 10.0 2.54 7.62 3.05 7.80 8.3 0.14 0.32 0.39 0.10 0.30 0.12 0.31 0.33 EUROPEAN PROJECTION SAA6588 SOT146 ( max. 0.254 2.0 0.01 0.078 ISSUE DATE 95-05-24 99-12-27 ...
Page 25
... REFERENCES JEDEC EIAJ MS-013 detail 1.1 1.1 1.4 0.25 0.25 0.4 1.0 0.043 0.043 0.055 0.01 0.01 0.016 0.039 EUROPEAN PROJECTION Product specification SAA6588 SOT163 ( 0.9 0.1 0 0.035 0.004 0.016 ISSUE DATE 97-05-22 99-12-27 ...
Page 26
... Use a low voltage ( less) soldering iron applied to the flat part of the lead. Contact time must be limited to 10 seconds 300 C. When using a dedicated tool, all other leads can be soldered in one operation within seconds between 270 and 320 C. 26 Product specification SAA6588 ...
Page 27
... Wave soldering is only suitable for SSOP and TSSOP packages with a pitch (e) equal to or larger than 0.65 mm definitely not suitable for packages with a pitch (e) equal to or smaller than 0.5 mm. 2002 Jan 14 PACKAGE suitable not suitable not suitable suitable not recommended not recommended 27 Product specification SAA6588 SOLDERING METHOD (1) WAVE REFLOW DIPPING (2) suitable suitable (3) suitable suitable ...
Page 28
... Product specification SAA6588 DEFINITIONS These products are not Philips Semiconductors ...
Page 29
... Purchase of Philips I components in the I Philips. This specification can be ordered using the code 9398 393 40011. 2002 Jan components conveys a license under the Philips’ system provided the system conforms to the I 29 Product specification SAA6588 2 C patent to use the 2 C specification defined by ...
Page 30
... Philips Semiconductors RDS/RBDS pre-processor 2002 Jan 14 NOTES 30 Product specification SAA6588 ...
Page 31
... Philips Semiconductors RDS/RBDS pre-processor 2002 Jan 14 NOTES 31 Product specification SAA6588 ...
Page 32
... Philips Semiconductors – a worldwide company Contact information For additional information please visit http://www.semiconductors.philips.com. For sales offices addresses send e-mail to: sales.addresses@www.semiconductors.philips.com. © Koninklijke Philips Electronics N.V. 2002 All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. ...