SC16C2550BIA44,512 NXP Semiconductors, SC16C2550BIA44,512 Datasheet - Page 6

• Manufacturer Part Number: SC16C2550BIA44,512
• Description: IC UART DUAL W/FIFO 44-PLCC
• Manufacturer: NXP Semiconductors

Specifications of SC16C2550BIA44,512

• Features: False-start Bit Detection
• Number Of Channels: 2, DUART
• Fifo's: 16 Byte
• Voltage - Supply: 3.5 V ~ 4.5 V
• With Auto Flow Control: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• With Cmos: Yes
• Mounting Type: Surface Mount
• Package / Case: 44-LCC (J-Lead)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935274407512; SC16C2550BIA44; SC16C2550BIA44

NXP Semiconductors
Table 3.
SC16C2550B_5
Product data sheet
Symbol
A0
A1
A2
CSA
CSB
D0
D1
D2
D3
D4
D5
D6
D7
GND
INTA
INTB
IOR
IOW
OP2A
OP2B
Pin
HVQFN32 DIP40 PLCC44 LQFP48
19
18
17
8
9
27
28
29
30
31
32
1
2
13
21
20
14
12
22
7
Pin description
5.2 Pin description
28
27
26
14
15
1
2
3
4
5
6
7
8
20
30
29
21
18
31
13
31
30
29
16
17
2
3
4
5
6
7
8
9
22
33
32
24
20
35
15
28
27
26
10
11
44
45
46
47
48
1
2
3
17
30
29
19
15
32
9
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Rev. 05 — 12 January 2009
Type
I
I
I
I
I
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I
O
O
I
I
O
O
Description
Address 0 select bit. Internal register address selection.
Address 1 select bit. Internal register address selection.
Address 2 select bit. Internal register address selection.
Chip Select A, B (active LOW). This function is associated
with individual channels, A through B. These pins enable data
transfers between the user CPU and the SC16C2550B for the
channel(s) addressed. Individual UART sections (A, B) are
addressed by providing a logic 0 on the respective CSA, CSB
pin.
Data bus (bidirectional). These pins are the 8-bit, 3-state data
bus for transferring information to or from the controlling CPU.
D0 is the least significant bit and the first data bit in a transmit
or receive serial data stream.
Signal and power ground.
Interrupt A, B (3-state). This function is associated with
individual channel interrupts, INTA, INTB. INTA, INTB are
enabled when MCR bit 3 is set to a logic 1, interrupts are
enabled in the Interrupt Enable Register (IER) and is active
when an interrupt condition exists. Interrupt conditions include:
receiver errors, available receiver buffer data, transmit buffer
empty or when a modem status flag is detected.
Read strobe (active LOW strobe). A logic 0 transition on this
pin will load the contents of an internal register defined by
address bits A0 to A2 onto the SC16C2550B data bus
(D0 to D7) for access by external CPU.
Write strobe (active LOW strobe). A logic 0 transition on this
pin will transfer the contents of the data bus (D0 to D7) from the
external CPU to an internal register that is defined by address
bits A0 to A2.
Output 2 (user-defined). This function is associated with
individual channels, A through B. The state at these pin(s) are
defined by the user and through MCR register bit 3. INTA, INTB
are set to the active mode and OP2 to logic 0 when MCR[3] is
set to a logic 1. INTA, INTB are set to the 3-state mode and
OP2 to a logic 1 when MCR[3] is set to a logic 0. See
“Modem Control Register bits
Since these bits control both the INTA, INTB operation and
OP2 outputs, only one function should be used at one time, INT
or OP2.
description”, bit 3 (MCR[3]).
SC16C2550B
© NXP B.V. 2009. All rights reserved.
Table 18
6 of 43