SA614AD NXP Semiconductors, SA614AD Datasheet
SA614AD
Specifications of SA614AD
Available stocks
Related parts for SA614AD
SA614AD Summary of contents
Page 1
RF COMMUNICATIONS PRODUCTS SA614A Low power FM IF system Product specification Replaces data of December 15, 1994 IC17 Data Handbook Philips Semiconductors 1997 Nov 07 ...
Page 2
... Intermediate frequency amplification and detection up to 25MHz RF level meter Spectrum analyzer Instrumentation FSK and ASK data receivers TEMPERATURE RANGE ORDER CODE -40 to +85 C SA614AN -40 to +85 C SA614AD 2 Product specification SA614A IF AMP INPUT IF AMP DECOUPLING IF AMP OUTPUT GND LIMITER INPUT LIMITER DECOUPLING ...
Page 3
Philips Semiconductors Low power FM IF system BLOCK DIAGRAM 16 15 REGULATOR GND 1 2 ABSOLUTE MAXIMUM RATINGS SYMBOL V Single supply voltage CC T Storage temperature range STG T Operating ambient temperature range SA614A A Thermal impedance JA DC ...
Page 4
Philips Semiconductors Low power FM IF system AC ELECTRICAL CHARACTERISTICS Typical reading +6V, unless otherwise stated +8kHz peak deviation. Audio output with C-message weighted filter and de-emphasis capacitor. Test circuit Figure ...
Page 5
Philips Semiconductors Low power FM IF system NE614A TEST CIRCUIT C 1 INPUT 100nF + 80 – 20% 63V K10000–25V Ceramic 100nF +10% 50V C2 100nF +10% 50V C3 100nF +10% 50V C4 C5 100nF +10% ...
Page 6
Philips Semiconductors Low power FM IF system 42k 1.6k 40k FULL WAVE RECT VOLT VOLT REG REG BAND GAP VOLT V CC 80k GND 1997 Nov GND 700 ...
Page 7
Philips Semiconductors Low power FM IF system 0.5 to 1.3 H 22pF 1nF 5.5 H 5.6pF + 100nF 6.8 F 10nF SA602 1 2 47pF 0.21 to 0.28 H 22pF 100nF Figure 5. Typical Application Cellular Radio (45MHz ...
Page 8
Philips Semiconductors Low power FM IF system 42k 40k Figure 7. Second Limiter and Quadrature Detector HIGH IMPEDANCE BPF a. Terminating High Impedance Filters with Transformation to Low Impedance BPF b. Low Impedance Termination and Gain Reduction ...
Page 9
Philips Semiconductors Low power FM IF system input level, the limited signal will begin to dominate the regeneration, and the demodulator will begin to operate in a “normal” manner. There are three primary ways to deal with regeneration: (1) Minimize ...
Page 10
Philips Semiconductors Low power FM IF system From the above equation, the phase shift between nodes 1 and 2, or the phase across C will be ...
Page 11
Philips Semiconductors Low power FM IF system optimized at 0.22 V for 12dB SINAD with minor change in the RSSI linearity. Any application which requires optimized RSSI linearity, such as spectrum analyzers, cellular radio, and certain types of telemetry, will ...
Page 12
Philips Semiconductors Low power FM IF system DIP16: plastic dual in-line package; 16 leads (300 mil) 1997 Nov 07 12 Product specification SA614A SOT38-4 ...
Page 13
Philips Semiconductors Low power FM IF system SO16: plastic small outline package; 16 leads; body width 3.9 mm 1997 Nov 07 13 Product specification SA614A SOT109-1 ...
Page 14
Philips Semiconductors Low power FM IF system Data Sheet Identification Product Status Objective Specification Formative or in Design Preliminary Specification Preproduction Product Product Specification Full Production Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, ...