GS880Z36AT-166 GSI TECHNOLOGY, GS880Z36AT-166 Datasheet - Page 12

• Manufacturer Part Number: GS880Z36AT-166
• Manufacturer: GSI TECHNOLOGY

Specifications of GS880Z36AT-166

• Density: 9Mb
• Access Time (max): 7ns
• Sync/async: Synchronous
• Architecture: SDR
• Clock Freq (max): 142.8MHz
• Operating Supply Voltage (typ): 2.5/3.3V
• Address Bus: 18b
• Package Type: TQFP
• Operating Temp Range: 0C to 70C
• Number Of Ports: 1
• Supply Current: 155mA
• Operating Supply Voltage (min): 2.3/3V
• Operating Supply Voltage (max): 2.7/3.6V
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 100
• Word Size: 36b
• Number Of Words: 256K
• Lead Free Status / Rohs Status: Not Compliant

Sleep Mode
During normal operation, ZZ must be pulled low, either by the user or by it’s internal pull down resistor. When ZZ is pulled high,
the SRAM will enter a Power Sleep mode after 2 cycles. At this time, internal state of the SRAM is preserved. When ZZ returns to
low, the SRAM operates normally after ZZ recovery time.
Sleep mode is a low current, power-down mode in which the device is deselected and current is reduced to I
Sleep mode is dictated by the length of time the ZZ is in a high state. After entering Sleep mode, all inputs except ZZ become
disabled and all outputs go to High-Z The ZZ pin is an asynchronous, active high input that causes the device to enter Sleep mode.
When the ZZ pin is driven high, I
operations or operations in progress may not be properly completed if ZZ is asserted. Therefore, Sleep mode must not be initiated
until valid pending operations are completed. Similarly, when exiting Sleep mode during tZZR, only a deselect or read commands
may be applied while the SRAM is recovering from Sleep mode.
Designing for Compatibility
The GSI NBT SRAMs offer users a configurable selection between Flow Through mode and Pipeline mode via the FT signal
found on Pin 14. Not all vendors offer this option, however most mark Pin 14 as V
through parts. GSI NBT SRAMs are fully compatible with these sockets.
Pin 66, a No Connect (NC) on GSI’s GS880Z18A/36 NBT SRAM, the Parity Error open drain output on GSI’s GS881Z18/36A
NBT SRAM, is often marked as a power pin on other vendor’s NBT compatible SRAMs. Specifically, it is marked V
on pipelined parts and V
feature may want to design the board site for the RAM with Pin 66 tied high through a 1k ohm resistor in Pipeline mode
applications or tied low in Flow Through mode applications in order to keep the option to use non-configurable devices open. By
using the pull-up resistor, rather than tying the pin to one of the power rails, users interested in upgrading to GSI’s ByteSafe NBT
SRAMs (GS881Z18/36A), featuring Parity Error detection and JTAG Boundary Scan, will be ready for connection to the active
low, open drain Parity Error output driver at Pin 66 on GSI’s TQFP ByteSafe RAMs.
Rev: 1.03 11/2004
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
CK
ZZ
SS
on flow through parts. Users of GSI NBT devices who are not actually using the ByteSafe™ parity
SB
2 is guaranteed after the time tZZI is met. Because ZZ is an asynchronous input, pending
tKC
tKC
tKH
tKH
Sleep Mode Timing Diagram
tZZS
tKL
tKL
12/23
tZZH
GS880Z18/36AT-250/225/200/166/150/133
DD
or V
DDQ
tZZR
on pipelined parts and V
SB
© 2001, GSI Technology
2. The duration of
DD
SS
or V
on flow
DDQ