IDT821068PX IDT, Integrated Device Technology Inc, IDT821068PX Datasheet - Page 18

IDT821068PX

Manufacturer Part Number
IDT821068PX
Description
Manufacturer
IDT, Integrated Device Technology Inc
Type
General Purposer
Datasheet

Specifications of IDT821068PX

Number Of Adc's
8
Number Of Dac's
8
Interface Type
Serial
Power Supply Type
Analog/Digital
Operating Supply Voltage (min)
4.75V
Operating Supply Voltage (typ)
5V
Operating Supply Voltage (max)
5.25V
Pin Count
128
Operating Temperature (min)
-40C
Operating Temperature (max)
85C
Screening Level
Industrial
Package Type
PQFP
Mounting
Surface Mount
Lead Free Status / Rohs Status
Not Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
IDT821068PX
Manufacturer:
IDT
Quantity:
5 510
Part Number:
IDT821068PX
Manufacturer:
SANYO
Quantity:
5 510
Part Number:
IDT821068PX
Manufacturer:
IDT
Quantity:
359
Part Number:
IDT821068PX
Manufacturer:
IDT
Quantity:
20 000
Part Number:
IDT821068PX8
Manufacturer:
IDT
Quantity:
5 510
Part Number:
IDT821068PX8
Manufacturer:
DALLAS
Quantity:
5 510
output to LMRL and LMRH. When L/C bit is 0, compressed PCM will
be output transparently to LMRH.
Application Note.
TELETAX
calling time and tariff. The frequency of teletax signal carrier can be
selected as 12 kHz or 16 kHz (± 50 Hz) by Global Command 19,
while the amplitude of the teletax signal on specific channel can be
programmed by Teletax Gain Setting bits (TGS[7:0]) in Local Com-
mand 3. When a ‘1’ appears on Teletax Ramp Start bit (RS) of Local
Command 10, the teletax signal will be output from the VOUT pin on
the corresponding channel with a 16 ms ± 10% rising time. This
teletax signal will last until a ‘0’ on the RS bit for the same channel. It
has a falling time of 16 ms ± 10%, as shown in Figure 12.
IDT821068 OCTAL PROGRAMMABLE PCM CODEC
The calculation and method of level metering will be described in
The teletax signal is used to sum the telephone fee according to the
rising
time
Figure 12. Teletax Signal
falling time
pause
time
18
CHANNEL POWER DOWN/STANDBY MODE
independently by Local Command 10. When the channel is powered
down (enters into standby mode), PCM data transmission and
reception, D/A and A/D are disabled. In this way, power consumption
of the device can be reduced. When IDT821068 is powered up or
reset, all eight channels will be powered down. All circuits that contain
programmed information retain their data when powered down. In MPI
operation, MPI (Microprocessor Interface) is always active so that new
command could be received and executed. In GCI operation, the
monitor channel of any time slot is always on so that new command
could be accepted at any time.
POWER DOWN PLL/SUSPEND MODE
mode, the PLL block is turned off and DSP operation is disabled. This
mode saves much more power consumption than standby mode. In
this mode, only Global Command and Local Command can be
executed. RAM operation is disabled as internal clock has been
turned off. The PLL blocks can be powered down by Global
Command 25. Suspend mode can be entered by powering down PLL
and all channels.
Each individual channel of IDT821068 can be powered down
A suspend mode is offered to the whole chip to save power. In this
INDUSTRIAL TEMPERATURE RANGE

Related parts for IDT821068PX