MAX4053ACSE+ Maxim Integrated Products, MAX4053ACSE+ Datasheet - Page 10

• Manufacturer Part Number: MAX4053ACSE+
• Description: IC MULTIPLEXER TRPL 2X1 16SOIC
• Manufacturer: Maxim Integrated Products

Specifications of MAX4053ACSE+

• Function: Multiplexer
• Circuit: 3 x 2:1
• On-state Resistance: 100 Ohm
• Voltage Supply Source: Single, Dual Supply
• Voltage - Supply, Single/dual (±): 2 V ~ 16 V, ±2.7 V ~ 8 V
• Current - Supply: 1µA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.154", 3.90mm Width)
• Number Of Switches: Triple
• Switch Configuration: SPDT
• On Resistance (max): 100 Ohms
• On Time (max): 175 ns
• Off Time (max): 150 ns
• Off Isolation (typ): - 90 dB
• Supply Voltage (max): +/- 8 V
• Supply Voltage (min): +/- 2.7 V
• Supply Current: 0.1 uA
• Maximum Power Dissipation: 696 mW
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Description/function: Analog Switch
• Input Level: CMOS, TTL
• Minimum Operating Temperature: 0 C
• Off State Leakage Current (max): 0.1 nA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Low-Voltage, CMOS Analog
Multiplexers/Switches
(V+ = +5V, V- = -5V, GND = 0V, T
Note: NO, NC, and COM pins are identical and interchangeable. Any may be considered an input or output; signals pass equally
10
_____________________________________________________________Pin Descriptions
____________________________Typical Operating Characteristics (continued)
1, 2, 4, 5, 12,
MAX4051A
MAX4051/
13, 14, 15
______________________________________________________________________________________
10
11
16
—
—
—
—
—
—
—
—
—
—
—
3
6
7
8
9
well in both directions.
-10
-20
-30
-40
-50
-60
-70
-80
-90
0
0.01
11, 12, 14, 15
MAX4052A
MAX4052/
1, 2, 4, 5
INSERTION LOSS
PIN
10
13
16
—
—
—
—
—
—
—
—
—
—
3
6
7
8
9
0.1
FREQUENCY RESPONSE
OFF-ISOLATION
FREQUENCY (MHz)
50Ω IN/OUT
1
A
MAX4053A
MAX4053/
= +25°C, unless otherwise noted.)
ON PHASE
15
11
10
12
13
14
16
—
—
—
—
10
1
2
3
5
6
7
8
9
4
100 300
NO0B–NO3B
NO0A–NO3A
NO0–NO7
5
0
-5
-10
-15
-20
-25
-30
-35
-40
NAME
COMB
COMA
COMC
ADDC
ADDB
ADDA
COM
GND
NOC
NOB
NCB
NOA
NCA
NCC
INH
V+
V-
Analog Switch Inputs 0–7
Analog Switch Common
Analog Switch “B” Inputs 0–3
Analog Switch “B” Common
Analog Switch “B” Normally Open Input
Analog Switch “B” Normally Closed Input
Analog Switch “A” Normally Open Input
Analog Switch “A” Normally Closed Input
Digital Inhibit Input. Normally connect to GND. Can be driven
to logic high to set all switches off.
Negative Analog Supply Voltage Input. Connect to GND for
single-supply operation.
Ground. Connect to digital ground. (Analog signals have no
ground reference; they are limited to V+ and V-.)
Digital Address “C” Input
Digital Address “B” Input
Digital Address “A” Input
Analog Switch “A” Inputs 0–3
Analog Switch “A” Common
Analog Switch “C” Normally Closed Input
Analog Switch “C” Normally Open Input
Analog Switch “C” Common
Positive Analog and Digital Supply Voltage Input
0.01
100
0.1
10
1
10
V± = ±5V
600Ω IN AND OUT
TOTAL HARMONIC DISTORTION
100
FUNCTION
vs. FREQUENCY
FREQUENCY (Hz)
1k
10k