MT9234ZBA-V-NAM Multi-Tech Systems, MT9234ZBA-V-NAM Datasheet - Page 19

• Manufacturer Part Number: MT9234ZBA-V-NAM
• Description: MODEM V.92 DATA/FAX/VOICE WORLD
• Manufacturer: Multi-Tech Systems
• Series: MultiModem® ZBAr

Specifications of MT9234ZBA-V-NAM

• Data Format: V.34, V.92
• Baud Rates: -
• Interface: RS-232
• Voltage - Supply: -
• Mounting Type: Desktop
• Package / Case: 5.7" L x 4.3" W x 1.0" H (145mm x 109mm x 25mm)
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 881-1145

Your modem was thoroughly tested at the factory before it was shipped. If you are unable to make a successful connection, or
if you experience data loss or garbled characters during your connection, it is possible that the modem is defective. However,
it is more likely that the source of your problem lies elsewhere. The following symptoms are typical of problems you might
encounter:
None of the Indicators Light
When you turn on the modem, the LED indicators on the front panel should flash briefly as the modem runs a self-test. If the
LEDs remain off, the modem is probably not receiving power.
CAUTION:
damage the modem and void your warranty.
The Modem Does Not Respond to Commands
Multi-Tech Systems, Inc. MT9234ZBA-Series User Guide (S000387D)
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
None of the LEDs light when the modem is on.
The modem does not respond to commands.
The modem cannot connect when dialing.
The modem disconnects while online.
The modem cannot connect when answering.
File transfer is slower than it should be.
Data is being lost.
There are garbage characters on the monitor.
The modem doesn’t work with Caller ID.
Fax and data software can’t run at the same time.
Make sure the modem’s power switch is on, especially if you normally turn the modem on by turning on a power strip.
If the modem is plugged into a power strip, make sure the power strip is plugged in and its power switch is on.
Make sure the power supply is firmly connected to the modem and the power supply’s power cord is firmly connected
to both the power supply and the wall outlet or power strip.
If the power strip is on and the modem switch is on, try moving the power supply to another outlet on the power strip.
Test that the outlet is live by plugging another device, such as a lamp, into it.
The modem or power supply may be defective. If you have another Multi-Tech modem, try swapping modems. If the
problem goes away, the first modem or power supply might be defective.
Make sure the modem is plugged in and turned on. (See “None of the Indicators Light.”)
Make sure you are issuing the modem commands from data communication software, either manually in terminal
mode or automatically by configuring the software. (You cannot send commands to the modem from the DOS
prompt.)
Make sure you are in terminal mode in your data communication program, then type AT and press E
an OK response from your modem, your connections are good and the problem likely is in the connection setup in
your communication software.
If you don’t get an OK, the problem may still be in the communication software. Make sure you have done whatever is
necessary in your software to make a port connection. Not all communication programs connect to the COM port
automatically. Some connect when the software loads and remain connected until the program terminates. Others
can disconnect without exiting the program. The modem’s TR indicator lights to show that the software has taken
control of the modem through the COM port.
Your communication software settings may not match the physical port to which the modem is connected. The serial
cable might be plugged into the wrong connector—check your computer documentation to make sure. Or you might
have selected a COM port in your software other than the one the modem is physically connected to—compare the
settings in your software to the physical connection.
If the modem is on, the cable is plugged into the correct port, the communication software is configured correctly, and
you still don’t get an OK, the fault might be in the serial cable. Make sure it is firmly connected at both ends.
Is this the first time you have used the cable? If so, it may not be wired correctly. Check the cable description on the
packaging to make sure the cable is the right one for your computer.
Peripheral expansion cards, such as sound and game cards, might include a serial port preconfigured as COM1 or
COM2. The extra serial port, or the card itself, may use the same COM port, memory address, or interrupt request
(IRQ) as your communication port. Be sure to disable any unused ports.
Do not under any circumstances replace the power supply with one designed for another product; doing so can
Chapter 6 – Troubleshooting
Chapter 6 – Troubleshooting
NTER
. If you get
19