MAX9257GTL+ Maxim Integrated Products, MAX9257GTL+ Datasheet - Page 21

• Manufacturer Part Number: MAX9257GTL+
• Description: IC SER/DESER PROG 40-TQFN
• Manufacturer: Maxim Integrated Products

Specifications of MAX9257GTL+

• Function: Serializer/Deserializer
• Data Rate: 840Mbps
• Input Type: Serial
• Output Type: LVDS
• Number Of Inputs: 16
• Number Of Outputs: 1
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 40-TQFN Exposed Pad
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Table 1. MAX9257 Power-Up Default Register Map (continued)
Table 2. MAX9258 Power-Up Default Register Map (see the MAX9258 Register Table )
REGISTER NAME
REGISTER NAME
REG11
REG12
REG13
REG14
REG0
REG1
REG2
REG3
REG4
REG5
REG6
REG7
Fully Programmable Serializer/Deserializer
______________________________________________________________________________________
ADDRESS (hex)
ADDRESS (hex)
REGISTER
REGISTER
0x0B
0x0C
0x0D
0x0E
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
POWER-UP VALUE
POWER-UP VALUE
with UART/I
(hex)
(hex)
0xB5
0xA0
0xA0
0x00
0xE0
0x00
0x00
0x00
0x20
0xF8
0xFF
0x00
GPIO7 = 0
GPIO6 = 0
GPIO5 = 0
GPIO4 = 0
GPIO3 = 0
GPIO2 = 0
GPIO1 = 0
GPIO0 = 0
PREEMP = 111, preemphasis = 0%
Reserved = 00000
Reserved = 000000
I2CFILT = 00, I
1) 95kbps to 400kbps = 100ns
2) 400kbps to 1000kbps = 50ns
3) 1000kbps to 4250kbps = 10ns
Reserved = 0000 000
LOCKED = read only
PRATE = 10, 20MHz to 40MHz
SRATE = 11, 400Mbps to 840Mbps
PAREN = 0, parity disabled
PWIDTH = 101, parallel data width = 18
SPREAD = 00, spread spectrum = off
AER = 0, error count is reset by reading error registers
Reserved = 0 0000
STODIV = 1010, STO clock is pixel clock divided by 1024
STOCNT = 0000, STO counter counts to 1
ETODIV = 1010, ETO clock is pixel clock divided by 1024
ETOCNT = 0000, ETO counter counts to 1
VEDGE = 0, VSYNC active edge is falling
HEDGE = 0, HSYNC active edge is falling
CKEDGE = 1, pixel clock active edge is rising
Reserved = 0000
PRBSEN = 0, PRBS test disabled
MAX9258 address = 1111 1000
End frame = 1111 1111
INTMODE = 0, interface with peripheral is UART
INTEN = 0, interface with peripheral is disabled
FAST = 0, UART bit rate = DC to 4.25Mbps
CTO = 000, never come back
BITRATE = 00, base mode bit rate = 95kbps to 400kbps
2
C Control Channel
POWER-UP DEFAULT SETTINGS
POWER-UP DEFAULT SETTINGS
2
C glitch filter settings:
21