SAA7134HL/V1,557 NXP Semiconductors, SAA7134HL/V1,557 Datasheet - Page 40

• Manufacturer Part Number: SAA7134HL/V1,557
• Description: IC AUD/VID DECODER PCI 128LQFP
• Manufacturer: NXP Semiconductors
• Type: Video Decoderr

Specifications of SAA7134HL/V1,557

• Package / Case: 128-LQFP
• Applications: TV
• Voltage - Supply, Analog: 3 V ~ 3.6 V
• Voltage - Supply, Digital: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 935269247557; SAA7134HLBE; SAA7134HLBE

Philips Semiconductors
Table 19:
V
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10] See User manual SAA7130HL/34HL for Anti-Alias Filter (AAF).
[11] Definition of levels and level setting:
SAA7134HL_4
Product data sheet
Symbol
VSB data output signals with respect to signal ADC_CLK
C
t
t
TS capture inputs with parallel transport streaming (TS-P); e.g. DVB applications
Clock input signal TS_CLK on pin GPIO20; see
T
t
t
Data and control input signals on TS-P port (with respect to signal TS_CLK) on pins GPIO0 to GPIO7, GPIO16, GPIO19
and GPIO22; see
t
t
TS capture inputs with serial transport streaming (TS-S); e.g. DVB applications
Clock input signal TS_CLK on pin GPIO20; see
T
t
t
Data and control input signals on TS-S port (with respect to signal TS_CLK) on pins GPIO16, GPIO19, GPIO21 and
GPIO22; see
t
t
h
PD
r
f
su(D)
h(D)
r
f
su(D)
h(D)
DDD
cy
cy
L
Input leakage currents include high-impedance output leakage for all bidirectional buffers with 3-state outputs.
Pins without pull-up resistors must have a 3 mA output current. Pins requiring pull-up resistors must have 6 mA; these are
pins FRAME#, TRDY#, IRDY#, DEVSEL#, SERR#, PERR#, INT_A and STOP#.
This parameter is to be interpreted as the cumulative edge rate across the specified range, rather than the instantaneous rate at any
point within the transition range.
REQ# and GNT# are point-to-point signals and have different output valid delay and input setup times than bused signals. GNT# has a
setup time of 10 ns. REQ# has a setup time of 12 ns.
For purposes of active or float timing measurements, the high-impedance or ‘off’ state is defined to be when the total current delivered
through the device is less than or equal to the leakage current specification.
RST_N is asserted and de-asserted asynchronously with respect to CLK.
All output drivers floated asynchronously when RST_N is active.
V
Nominal analog video input signal is to be terminated by 75
into 18
from 3 dB (attenuation) to +6 dB (amplification) for the internal automatic gain control. See also Application note SAA7130HL/34HL .
= 3.0 V to 3.6 V; V
DD(I2C)
is the extended pull-up voltage of the I
Characteristics
Parameter
load capacitance
data hold time
propagation delay from
positive edge of
signal ADC_CLK
cycle time
duty factor
rise time
fall time
input data setup time
input data hold time
cycle time
duty factor
rise time
fall time
input data setup time
input data hold time
and 56 , and the dividing tap should feed the video input pin, via a coupling capacitor of 47 nF, to achieve a control range
Figure 16
Figure 16
DDA
= 3.0 V to 3.6 V; T
…continued
Conditions
inverted and not delayed
inverted and not delayed
0.8 V to 2.0 V
2.0 V to 0.8 V
0.8 V to 2.0 V
2.0 V to 0.8 V
2
amb
C-bus (3.3 V or 5 V bus).
Figure 16
Figure 16
= 25 C; unless otherwise specified.
Rev. 04 — 31 March 2006
that results in 1 V (p-p) amplitude. This termination resistor should be split
[18] [20]
[18]
[17]
[17]
Min
25
5
-
-
40
-
-
2
5
37
40
-
-
2
5
PCI audio and video broadcast decoder
© Koninklijke Philips Electronics N.V. 2006. All rights reserved.
Typ
-
-
-
333
-
-
-
-
-
-
-
-
-
-
-
SAA7134HL
Max
50
-
23
-
60
5
5
-
-
-
60
5
5
-
-
Unit
pF
ns
ns
ns
%
ns
ns
ns
ns
ns
%
ns
ns
ns
ns
40 of 51