ELC-ACPGMXFR Eaton / Control Automation, ELC-ACPGMXFR Datasheet - Page 2

• Manufacturer Part Number: ELC-ACPGMXFR
• Description: ACCESSORY; ELC CONTROLLER PROGRAM TRANSFER MODULE
• Manufacturer: Eaton / Control Automation
• Type: Programmingr

Specifications of ELC-ACPGMXFR

• Brand/series: ELC
• Primary Type: Option
• For Use With: Micro Controllers

3.1 Read/Write Operation Sequence:
3.2 Password Function
3.3 The conditions when ACPGMXFR read/write to ELC:(w/ PW: with password; w/o PW: without
3.4 ACPGMXFR Data Erase function:
Once ACPGMXFR connects to ELC, please press the data erase bottom within 5 seconds. After “OK” LED turning on, release
the bottom and disconnect the ACPGMXFR from ELC.
3.5 Data Duplication Function
Step
1.) Set M1085 On/Off in ELC
2.) Select ACPGMXFR RD/WR switch in reading or writing mode.
3.) Connect ACPGMXFR to ELC COM communication port
4.) After operation is completed, “OK” LED will turn on.
5.) Disconnect ACPGMXFR with the ELC.
1
2
3
4
Password
setting
ELC Status
password)
will verify password with ELC. Only if ACPGMXFR verify password correctly with ELC, ACPGMXFR can write data to
ELC. ACPGMXFR password setting method as follows:
1. Write the password to D1086 and D1087 and set M1086 on in ELC by ELCSoft or ELC-HHP.
2. Set the WR/RD switch to “RD” mode, and connect the ACPGMXFR to ELC. Then ACPGMXFR will read data from
3. After Reading from ELC, ACPGMXFR will check M1086 status. If M1086 is on, ACPGMXFR keep on reading D1086
follows:
ACPGMXFR contain password function. If ELC protected by password and ACPGMXFR connect to ELC, ACPGMXFR
The password key has four digits. Each digit is 8bits number and form with ASCII in D1086 and D1087. Example as
ACPGMXFR can read/write program and parameters (coils and registers) from/to ELC. During ACPGMXFR reading
Data Duplication steps:
operating, ACPGMXFR check M1085 status to deciding whether reading the parameters or not. When M1085 is on,
ACPGMXFR will not read the parameters from ELC, otherwise it will read the parameters. During ACPGMXFR Writing
operating, ACPGMXFR check M1085 status to deciding whether writing the parameters or not. When M1085 is on,
ACPGMXFR will not write the parameters to ELC, otherwise it will write the parameters.
STOP
RUN
ASCII code (HEX)
Set RD/WR switch to “RD” mode
Connect ACPGMXFR to ELC COM with 5 sec. waiting.
After reading data from ELC, “OK” LED will light
Disconnect ACPGMXFR when read process is done.
ELC.
and D1087. ACPGMXFR take D1086 and D1087 as the password key. After reading D1086 and D1087,
ACPGMXFR finish the transmission and turn on “OK” LED. If M1086 is off, ACPGMXFR turn on “OK” LED
immediately. When “OK” LED is on, disconnect the ACPGMXFR from ELC.
Password Key
ACPGMXFR
w/o PW
w/o PW
w/ PW
w/ PW
(ELC→ACPGMXFR) RD (Read)
Unable to read
Unable to read
1 (0x31=H31)
Able to read
Able to read
High byte
w/o PW
Byte 1
Read
D1086
Password verify error
Password verify error
Unable to read
Unable to read
2 (0x32=H32)
w/ PW
Low byte
Byte 2
2
Set RD/WR switch to “WR” mode and confirm ELC is
STOP status
Connect ACPGMXFR to ELC COM with 5 sec. waiting.
After Writing data to ELC, “OK” LED will light
Disconnect ACPGMXFR when write process is done.
Password verify error
(ELC←ACPGMXFR) WR (Write)
Unable to write
Unable to write
Able to write
3 (0x33=H33)
w/o PW
High byte
Byte 3
Write
D1087
Able to write and write
password to ELC
Able to write after
verification
Unable to write
Unable to write
4 (0x34=H34)
IL05003020E.pdf
Low byte
w/ PW
Byte 4