AAT3681IJS-4.2-T1 Analogic Tech, AAT3681IJS-4.2-T1 Datasheet - Page 11

• Manufacturer Part Number: AAT3681IJS-4.2-T1
• Description: Battery Management USB Port/Ad Lith-Ion Polymer
• Manufacturer: Analogic Tech

Specifications of AAT3681IJS-4.2-T1

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Application Information
Adapter or USB Power Input
Constant current charge levels up to 300mA may be
programmed by the user when powered from a sufficient
input power source. The AAT3681 will operate from the
adapter input over a 4.0V to 7.5V range. The constant
current fast charge current for the adapter input is set
by the R
Refer to Table 1 for recommended R
desired constant current charge level.
Adapter Input Charge Inhibit and Resume
The AAT3681 has a UVLO and power on reset feature so
that if the input supply to the ADP pin drops below the
UVLO threshold, the charger will suspend charging and
shut down. When power is re-applied to the ADP pin or
the UVLO condition recovers, the system charge control
will assess the state of charge on the battery cell and will
automatically resume charging in the appropriate mode
for the condition of the battery.
Enable / Disable
The AAT3681 provides an enable function to control the
charger IC on and off. The enable (EN) pin is internally
pulled down. When pulled to a logic high level, AAT3681
is enabled. When left open or pulled to a logic low level,
the AAT3681 will be shut down and forced into the sleep
state. Charging will be halted regardless of the battery
voltage or charging state. When the device is re-enabled,
the charge control circuit will automatically reset and
resume charging functions with the appropriate charging
mode based on the battery charge state and measured
cell voltage on the BAT pin.
Programming Charge Current
The fast charge constant current charge level is user
programmed with a set resistor placed between the ISET
pin and ground. The accuracy of the fast charge, as well
as the preconditioning trickle charge current, is domi-
nated by the tolerance of the set resistor used. For this
reason, a 1% tolerance metal film resistor is recom-
mended for the set resistor function. Fast charge con-
stant current levels from 15mA to 300mA may be set by
selecting the appropriate resistor value from Table 1.
BatteryManager
3681.2009.03.1.6
SET
resistor connected between ISET and ground.
TM
USB Port or AC Adapter Lithium-Ion/Polymer Battery Charger
SET
values for a
w w w . a n a l o g i c t e c h . c o m
Protection Circuitry
Over-Voltage Protection
An over-voltage event is defined as a condition where
the voltage on the BAT pin exceeds the maximum bat-
tery charge voltage and is set by the over-voltage pro-
tection threshold (V
occurs, the AAT3681 charge control will shut down the
device until voltage on the BAT pin drops below V
AAT3681 will resume normal charging operation after
the over-voltage condition is removed.
Over-Temperature Shutdown
The AAT3681 has a thermal protection control circuit
which will shut down charging functions should the inter-
nal die temperature exceed the preset thermal limit
threshold. Once the internal die temperature falls below
the thermal limit, normal operation will resume the pre-
vious charging state.
1000
100
10
I
Figure 2: Constant Charging Current
1
CHARGE
1
Nominal
300
250
200
150
100
50
40
30
20
15
(mA)
vs. Set Resistor Values.
Table 1: R
PRODUCT DATASHEET
OVP
10
). If an over-voltage condition
R
SET
SET
(kΩ Ω )
AAT3681
Values.
Set Resistor
100
Value (kΩ)
5.36
6.49
8.06
10.7
16.2
31.6
38.3
53.6
78.7
105
OVP
1000
. The
11