EMC2102-DZK-TR SMSC, EMC2102-DZK-TR Datasheet - Page 37

• Manufacturer Part Number: EMC2102-DZK-TR
• Description: Industrial Temperature Sensors RPM Fan Contrllr
• Manufacturer: SMSC

Specifications of EMC2102-DZK-TR

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

RPM-Based Fan Controller with HW Thermal Shutdown
Datasheet
SMSC EMC2102
6.7
6.8
24h
ADDRESS
23h
ADDRESS
Interrupt
Status
Register 2
The Interrupt Status Registers report the operating condition of the EMC2102. If any of the bits (except
the PWROK, THERM, and HWS bits) are asserted then the ALERT# pin will be asserted low. Reading
from the status register clears all status bits if the error conditions is removed. If there are no set status
bits, then the ALERT# pin will be released.
Bit 7 - PWROK - this bit is set if the POWER_OK pin is set to a logic ‘1’ state. When this bit is set, it
will not cause the ALERT# pin to be asserted.
Bit 6 - THERM - this bit is set if the THERMTRIP# pin is set to a logic ‘0’ state. When this bit is set,
it will not cause the ALERT# pin to be asserted however will coincide with SYS_SHDN# pin being
asserted. The THERMTRIP# pin can only cause the SYS_SHDN# pin to be asserted if the
POWER_OK pin is set to a logic ‘1’ (see Figure 5.4, "EMC2102 Critical/Thermal Shutdown Block
Diagram").
Bit 5 - HWS - this bit is set if the internal HW_SHDN signal is set (see
HW_SHDN
bit is set, it will not cause the ALERT# pin to be asserted however will coincide with SYS_SHDN# pin
being asserted.
Bit 3 - WATCH - this bit is asserted ‘1’ if the Watchdog Timer circuit does not detect the fan being
programmed within 4 seconds after power-up. This bit cannot be masked.
Bit 2 - FAN_SPIN - this bit is asserted ‘1’ if the Spin up Routine for Fan cannot detect a valid TACH
within its maximum time window. This bit can be masked from asserting the ALERT# pin.
Bit 1 - FAN_STALL - this bit is asserted ‘1’ if the TACH measurement on fan detects a stalled fan. This
bit can be masked from asserting the ALERT# pin.
Bit 0 - I_SHORT - this bit is asserted ‘1’ if the High Side Fan Driver circuit detects a short circuit
condition. This bit cannot be masked.
The Interrupt Mask Register controls the masking for each temperature channel and the TACH monitor.
When a channel is masked, it will not cause the ALERT# pin to be asserted when an error condition
is detected.
Bit 4 - SPIN_MASK - masks the FAN_SPIN bit from asserting the ALERT# pin.
Interrupt Status Register 2
Interrupt Mask Register
REGISTER
Interrupt
Mask
REGISTER
‘0’ - the FAN_SPIN bit will assert the ALERT# pin if set in the Interrupt Status Register 2.
‘1’ - (default) - the FAN_SPIN bit will not assert the ALERT# pin though will still update the Interrupt
Status Register 2 normally.
Signal") based on the TRIP_SET voltage and the SHDN_SEL pin conditions. When this
PWROK
B7
-
B7
Table 6.10 Interrupt Status Register 2
-
THERM
B6
Table 6.11 Interrupt Mask Register
B6
-
B5
DATASHEET
HWS
B5
SPIN_
MASK
B4
37
-
B4
STALL_
MASK
WATCH
B3
B3
EXT3_
MSK
FAN_S
PIN
B2
B2
EXT2_
MSK
FAN_S
TALL
B1
B1
Section 5.7.3, "Internal
EXT1_
MSK
Revision 2.02 (05-17-07)
I_SHO
RT
B0
B0
10h
DEFAULT
00h
DEFAULT