HG2-SSUL Panasonic, HG2-SSUL Datasheet

HG2-SSUL

Manufacturer Part Number

HG2-SSUL

Description

Relay Sockets & Hardware HG2 Relay Socket (Solder Terminal)

Manufacturer

Panasonic

Datasheet

1.HG2-SSUL.pdf (5 pages)

Current page: 1 of 5
Download datasheet (217Kb)

SPECIFICATIONS

Contacts

Expected life (min. operations)

Life curve for AC types

#1 This value can change due to the switching frequency, environmental conditions,

Remarks

* Speciﬁcations will vary with foreign standards certiﬁcation ratings.

Electrical life with AC load

Note: In case of an electromagnet or exiting coil load (solenoid, etc.), the value of the motor or lamp load is applicable.

Electrical life with DC load

Note: For DC inductive load, use of an arc extinguishing circuit is recommended.

Arrangement

Initial contact resistance, max.

(By voltage drop 6 V DC 1A)

Contact material

Nominal switching capacity

Min. switching capacity

Mechanical (at 180 cpm)

Measurement at same location as “Initial breakdown voltage” section

and desired reliability level, therefore it is recommended to check this with the

actual load.

(cos ϕ ] 0.4)

(cos ϕ ] 1)

Resistive

Inductive

AC load

Inductive (L/R ] 7 ms)

Resistive

1,000

DC load

900

800

700

600

500

400

300

200

100

Voltage, V AC

125

250

125

250

Mechanical life : 10

1.417

2.205

Operating frequency:

180 op./min.

Load current, A

inch

2 Form C, 3 Form C, 4 Form C

Current, A

AC type: 10

20 A 250 V AC (resistive)

7.5

100 mA, 5 V DC

20 AMP POWER RELAY

Silver alloy

15 mΩ

HG2

HG3

HG4

, DC type: 10

(min. operations)

Voltage, V DC

Expected life

7.5×10

5×10

2×10

5×10

2×10

5×10

2×10

5×10

125

34.0

50.0

68.0

1.339

1.969

2.667

FEATURES

• Large capacity — 20 A 250 V AC resistive and 1.5 kW 3 phase

• High contact reliability after long use

• Usable with direct soldering,

quick-connect and plug-in terminals. (.250)

Characteristics (at 60 Hz, 20°C 68°F)

Maximum operating speed

Initial insulation resistance*

Initial

breakdown

voltage*

Operate time*

(at nominal voltage)

Release time

(without diode)*

(at nominal voltage)

Shock resistance

Vibration resistance

Conditions for operation,

transport and storage*

(Not freezing and condensing at

low temperature)

Unit weight

Motor

Detection current: 10 mA

Excluding contact bounce time

Half-wave pulse of sine wave: 11ms; detection time: 10µs

Half-wave pulse of sine wave: 6ms

Detection time: 10µs

Refer to 6. Conditions for operation, transport and storage mentioned in

AMBIENT ENVIRONMENT

AC load

Lamp

Current, A

Single

phase

Three

phase

0.8

0.4

Between open contacts

Between contacts sets

Between contacts and coil

(approx.)

Voltage, V AC

HG RELAYS

220 V AC motor loads

125

250

2 Form C type

3 Form C &

4 Form C type

2 Form C type

3 Form C &

4 Form C type

Functional*

Destructive*

Functional*

Destructive

2 Form C type

3 Form C type

4 Form C type

Ambient

temp.

Humidity

Expected life (min. operations)

Capacity, kW

0.75

0.5

0.3

0.4

1.5

98 m/s

at 1 mm double amplitude

at 2 mm double amplitude

Min. 100 MΩ at 500 V DC

contact moving direction)

Approx. 130 g

Approx. 185 g

Approx. 240 g

5 × 10

2,000 Vrms for 1 min.

980 m/s

–58°F to +104°F

–50°C to +40°C

5 to 85% R.H.

{10 G} (except for the

Max. 30 ms

Max. 40 ms

Max. 30 ms

Max. 40 ms

10 to 55 Hz

20 cpm

(min. operations)

Expected life

{100 G}

2×10

5×10

2×10

5×10

2×10

5×10

2×10

5×10

4.59 oz

6.53 oz

8.47 oz

Related parts for HG2-SSUL

HG2-SSUL Summary of contents

Page 1

... Note: For DC inductive load, use of an arc extinguishing circuit is recommended. All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd. 20 AMP POWER RELAY FEATURES • Large capacity — 250 V AC resistive and 1 phase • High contact reliability after long use a HG2 34.0 1.339 • Usable with direct soldering, HG3 50.0 1.969 quick-connect and plug-in terminals ...

Page 2

... For AC types, when operating voltage is 70% of nominal coil voltage, “buzzing” will ORDERING INFORMATION Ex. HG Contact arrangement 2: 2 Form Form Form C (Note) Standard packing Carton: HG2 20 pcs. UL/CSA approved type is standard. Pick-up Drop-out voltage, voltage, allowable (max (min voltage 4 ...

Page 3

... DIMENSIONS HG2 (2 Form C) 8.4 2.5 DIA. 9 DEEP HOLE for 7 .331 3 DIA. TAPPING SCREW .276 .098 DIA. .354 DEPTH 20.5 16 .807 .630 2.5 DIA. 8 DEEP HOLE for 3 DIA. TAPPING SCREW .098 DIA. .315 DEPTH 15 .591 36 34 1.417 1.339 56 2.205 8.5 .335 AMP SERIES ...

Page 4

... HOLD DOWN Lot No. CLIP ±1 80 ±.039 3.150 ±1 58 ±0.5 35.4 ±.039 2.283 ±.020 1.394 HG2 RELAY ±0.6 34.5 ±.024 1.358 ±0.6 36 ±.024 1.417 ±0.2 ±0 ±.008 ±.008 1.024 .394 1.024 ...

Page 5

... Socket Combinations NOTES Please use the hold-down clip whenever HG relays will be used in applications where strong vibrating or shock force occurs. When used in such applications, For Cautions for Use, see Relay Technical Information All Rights Reserved © COPYRIGHT Matsushita Electric Works, Ltd. ...

Related keywords

HG2-SSUL datasheet
HG2-SSUL data sheet
HG2-SSUL pdf datasheet
HG2-SSUL component
HG2-SSUL part
HG2-SSUL distributor
HG2-SSUL RoHS
HG2-SSUL datasheet download