EPF10K100ABC356-3 Altera, EPF10K100ABC356-3 Datasheet - Page 38

• Manufacturer Part Number: EPF10K100ABC356-3
• Description: IC FLEX 10KA FPGA 100K 356-BGA
• Manufacturer: Altera
• Series: FLEX-10K®r

Specifications of EPF10K100ABC356-3

• Number Of Logic Elements/cells: 624
• Number Of Labs/clbs: 624
• Total Ram Bits: 24576
• Number Of I /o: 274
• Number Of Gates: 158000
• Voltage - Supply: 3 V ~ 3.6 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 356-BGA
• Family Name: FLEX 10KA
• Number Of Usable Gates: 100000
• Number Of Logic Blocks/elements: 4992
• # Registers: 1218
• # I/os (max): 274
• Frequency (max): 125MHz
• Process Technology: CMOS
• Operating Supply Voltage (typ): 3.3V
• Logic Cells: 4992
• Ram Bits: 24567
• Device System Gates: 158000
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 356
• Package Type: BGA
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 544-2191

Output
Configuration
38
FLEX 10K Embedded Programmable Logic Device Family Data Sheet
Figure 17. Enabling ClockLock & ClockBoost in the Same Design
To use both the ClockLock and ClockBoost circuits in the same design,
designers must use Revision C EPF10K100GC503-3DX devices and
MAX+PLUS II software versions 7.2 or higher. The die revision is
indicated by the third digit of the nine-digit code on the top side of the
device.
This section discusses the peripheral component interconnect (PCI)
pull-up clamping diode option, slew-rate control, open-drain output
option, MultiVolt I/O interface, and power sequencing for FLEX 10K
devices. The PCI pull-up clamping diode, slew-rate control, and
open-drain output options are controlled pin-by-pin via Altera logic
options. The MultiVolt I/O interface is controlled by connecting V
a different voltage than V
software via the Global Project Device Options dialog box (Assign
menu).
PCI Clamping Diodes
The EPF10K10A and EPF10K30A devices have a pull-up clamping diode
on every I/O, dedicated input, and dedicated clock pin. PCI clamping
diodes clamp the transient overshoot caused by reflected waves to the
V
can also be used to limit overshoot in other systems.
Clamping diodes are controlled on a pin-by-pin basis via a logic option in
the Altera software. When V
diode turned on can be driven by a 2.5-V or 3.3-V signal, but not a 5.0-V
signal. When V
can be driven by a 2.5-V signal, but not a 3.3-V or 5.0-V signal. However,
a clamping diode can be turned on for a subset of pins, which allows
devices to bridge between a 3.3-V PCI bus and a 5.0-V device.
CCIO
value and are required for 3.3-V PCI compliance. Clamping diodes
gclk1
CCIO
CLKLOCK
CLKLOCK
is 2.5 V, a pin that has the clamping diode turned on
CCINT
CLOCKBOOST=1
INPUT_FREQUENCY=50
CLOCKBOOST=2
INPUT_FREQUENCY=50
CCIO
. Its effect can be simulated in the Altera
a
b
is 3.3 V, a pin that has the clamping
D
D
Q
Q
Altera Corporation
aout
bout
CCIO
to