EP3C10F256C8 Altera, EP3C10F256C8 Datasheet - Page 48

• Manufacturer Part Number: EP3C10F256C8
• Description: IC CYCLONE III FPGA 10K 256-FBGA
• Manufacturer: Altera
• Series: Cyclone® IIIr

Specifications of EP3C10F256C8

• Number Of Logic Elements/cells: 10320
• Number Of Labs/clbs: 645
• Total Ram Bits: 423936
• Number Of I /o: 182
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 256-FBGA
• For Use With: 544-2601 - KIT DEV CYCLONE III LS EP3CLS200544-2411 - KIT DEV NIOS II CYCLONE III ED.
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -
• Other names: 544-2416; EP3C10F256C8

2–4
Table 2–3. Cyclone III LS Devices Recommended Operating Conditions
Cyclone III Device Handbook, Volume 2
V
V
V
T
t
I
Notes to
(1) V
(2) V
(3) V
(4) Power-on reset (POR) time for Standard POR ranges from 50 to 200 ms. Each individual power supply must reach the recommended operating
(5) POR time for Fast POR ranges from 3 to 9 ms. Each individual power supply must reach the recommended operating range within 3 ms.
(6) All input buffers are powered by the V
RAM P
Diode
J
C CB AT
I
O
Symbol
locked-loops [PLLs}), and must be powered up and powered down at the same time.
range within 50 ms.
CC IO
CC D_P LL
CC
must rise monotonically.
Table
for all I/O banks must be powered up during device operation. All V
must always be connected to V
2–3:
Battery back-up power supply for design
security volatile key register
Input voltage
Output voltage
Operating junction temperature
Power supply ramptime
Magnitude of DC current across
PCI-clamp diode when enabled
DC Characteristics
This section lists the I/O leakage current, pin capacitance, on-chip termination (OCT)
tolerance, and bus hold specifications for Cyclone III LS devices.
Supply Current
Supply current is the current the device draws after the device is configured with no
inputs or outputs toggling and no activity in the device. Use the Excel-based Early
Power Estimator (EPE) to get the supply current estimates for your design because
these currents vary largely with the resources you use.
Table 2–4
Table 2–4. Cyclone III LS Devices I/O Pin Leakage Current
Symbol
I
I
Notes to
(1) This value is specified for normal device operation. The value varies during device power-up. This applies for all
(2) The 10 μA I/O leakage current limit is applicable when the internal clamping diode is off. A higher current can be
I
OZ
V
observed when the diode is on.
CC IO
Parameter
Table
settings (3.3, 3.0, 2.5, 1.8, 1.5, and 1.2 V).
Input Pin Leakage Current V
Tri-stated I/O Pin Leakage
Current
lists the I/O pin leakage current for Cyclone III LS devices.
C CIO
CCINT
2–4:
supply.
through a decoupling capacitor and ferrite bead.
Parameter
V
For commercial use
I
O
Standard POR
For industrial use
= V
= V
CCA
Fast POR
Conditions
Conditions
pins must be powered to 2.5 V (even when you do not use phase
CC IOM AX
CC IOMA X
—
—
—
—
(Note 1)
to 0 V
to 0 V
(5)
(4)
,
(2)
(Note 1)
Chapter 2: Cyclone III LS Device Data Sheet
(Part 2 of 2)
Min
–10
–10
50 µs
50 µs
–0.5
Min
–40
1.2
—
© December 2009 Altera Corporation
0
0
,
(2)
Typ
—
—
Typ
3.0
—
—
—
—
—
—
—
Electrical Characteristics
50 ms
Max
3 ms
Max
10
10
V
100
3.3
3.6
85
10
C CIO
Unit
Unit
mA
μA
μA
°C
°C
—
—
V
V
V