LQ150X1KW31 Sharp Electronics, LQ150X1KW31 Datasheet
LQ150X1KW31
Specifications of LQ150X1KW31
Related parts for LQ150X1KW31
LQ150X1KW31 Summary of contents
Page 1
... P S RODUCT PECIFICATIONS LQ150X1KW31 TFT LCD Module (Model No.: LQ150X1KW31) Spec. Issue Date: June 14, 2002 Liquid Crystal Displays Group ® ...
Page 2
...
Page 3
... LQ150X1KW31 SPEC No. DATE LD-14506 Jun.1 2002 LD-14506A Jun.14 2002 RECORDS OF REVISION SUMMARY REVISED No. PAGE - - 1 2,19, Change unit outline dimensions. 20.7(D) 22.3( Add packing form drawing NOTE - 1st Issue ...
Page 4
... Application This specification applies to a color TFT-LCD module, LQ150X1KW31 (15”XGA all in one module.). ◎These specification sheets are the proprietary product of SHARP CORPORATION(”SHARP) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...
Page 5
Overview This module is a all in one model using a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor composed of a color TFT-LCD panel, driver ICs, control circuit, power supply circuit, ...
Page 6
Block Diagram（Fig．3） DDC ADC Analog Analog-CN RGB PW2100 12VDC F-ROM PW114 CPU Graphic Timing Engine Controller DC/DC Inverter Key-pad (User correspondence) LD-14506A- 3 Source Driver Gate Driver Panel B/L System LCD ...
Page 7
Input Terminals 5-1. Analog video input The module-side connector ：S15B-PH-SM3(JST) CN1 The user-side connector Pin No. Symbol 1 RV Red Video 2 RG Red GND 3 GV Green Video 4 GG Green GND 5 BV Blue Video 6 ...
Page 8
Back light driving The back light system is an edge-lighting type with four CCFT (Cold Cathode Fluorescent Tube). The characteristics of the lamp are shown in the following table . The value mentioned below is at the case ...
Page 9
FUNCTION /Video Stretching and Down Scaling /Auto Correction -- display size, position, clock, Phase adjustment /Panel Timing and Interface /Controller ASICS –PW114 LD-14506A- 6 ...
Page 10
Output for Key-pad for Operation（ＣＮ４） Connector：SD53261-1510（molex） LEDG-ON 6 LEDO- Fig.4 Name Signal N.C. N.C. N.C. N.C. N.C. N.C. GND GND Green LED ON ...
Page 11
OSD MENU MENU FUNCTION MENU1 MANUAL ADJUSTMENT AUTO MENU2 MANUAL GAIN CONTROL AUTO MENU3 WHITE BALANCE MENU4 OSD H-POSITION MODE SELECT OSD V-POSITION 400 LINE EXPAND SCALING LANGUAGE (Key Function) * MENU : Change “OSD Menu” (MENU1 – ...
Page 12
Operation method of OSD 1) To use auto adjustment” at first. (13-4- use manual adjustment, if necessary. (13-4-2) [Memo] Adjustment record can be sustained even after the power- off. (However, it might not be sustained if ...
Page 13
Reset of adjustment value <Reset of ADJUSTMENT menu> The adjustment value of ADJUUSTMENT menu can be returned back to the initial condition, which was set up in the time of the factory’s shipping. i)To turn on the power ...
Page 14
ADJUSTMENT MANUAL AUTO CLOCK 127 PHASE 29 H-POS 200 V-POS 41 1024×768 6 0 ii)To press “+” button. The display turns black with “ADJUSTING” shown, then comes back ...
Page 15
After then, user can adjust the item which needs to be change. Everytime you press “MENU” button switched. (ADJUSTMENT → GAIN CONTROL → WHITE BALANCE → MODE SELECT → to make the menu disappear) [MEMO] The adjustment ...
Page 16
To select the item : “SELECT” button * next menu : “MENU” button <“Auto Gain Control” function> / Black level and Contrast are adjusted based upon the brightest color and the darkest color in the ...
Page 17
B-CONTRAST….. Yellow by “-“ button Blue by “+” button <MODE SELECT menu> MODE SELECT OSD H-POSITION OSD V-POSITION 400 LINES 640 EXPAND ON1 SCALING 3 LANGUAGE 1024×768 Depending on the resolution of input signal, the display ...
Page 18
Optical Characteristics Parameter Symbol View θ21,θ22 CR≧10 Horizontal Angle θ11 Vertical Range θ12 ＣＲn Contrast ratio τr Response Rise Time Decay τd Chromaticity x of White y Chromaticity x of Red y Chromaticity x of Green y Chromaticity ...
Page 19
The contrast ratio is defined as the following. Contrast Ratio (CR) ＝ 【Note3】Definition of response time: The response time is defined as the following figure and shall be measured by ...
Page 20
Handling Precautions a) Be sure to turn off the power supply when inserting or disconnecting the cable sure to design the cabinet so that the module can be installed without any extra stress such as warp ...
Page 21
... Lot No. and indication Label: SHARP LQ150X1KW31 28 XXXXXXX MADE IN JAPAN A production year (the last figures of the Christian 2) Packing box Label Barcode （１Ｔ）２００２．０８．２５ Barcode （Ｑ） Barcode シ ...
Page 22
sharp ...
Page 23
sharp ...
Page 24
sharp ...
Page 25
... Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp EUROPE SHARP Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com SINGAPORE SHARP Electronics (Singapore) PTE., Ltd. ...