LQ200T3LZ18 Sharp Electronics, LQ200T3LZ18 Datasheet
LQ200T3LZ18
Specifications of LQ200T3LZ18
Available stocks
Related parts for LQ200T3LZ18
LQ200T3LZ18 Summary of contents
Page 1
...
Page 2
...
Page 3
... Application This specification applies to the color 20.0” Wide XGA TFT-LCD module LQ200T3LZ18. * These specification sheets are proprietary products of SHARP CORPORATION (“SHARP”) and include materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of SHARP ...
Page 4
Input Terminals 4-1. TFT panel driving CN1 (Interface signals and +12V DC power supply) (Shown in Fig.1) Using connector ：FI-X30SSL-HF (Japan Aviation Electronics Ind. , Ltd.) Mating connector ：FI-X30HL,FI-X30HL-T, FI-X30C2L-NPB, FI-X30C2L-T-NPB,FI-X30M Mating LVDS transmitter：THC63LVDM83R or equivalent device Pin No. ...
Page 5
SELLVDS Transmitter Pin No Data 51 TA0 52 TA1 54 TA2 55 TA3 56 TA4 3 TA5 4 TA6 6 TB0 7 TB1 11 TB2 12 TB3 14 TB4 15 TB5 19 TB6 20 TC0 22 TC1 23 TC2 ...
Page 6
Diagram (LCD Module) O/S CONTROL SIGNALS FRAME O/S SET TEST TEMP3 TEMP2 TEMP1 INPUT SIGNALS Von V V BRT-A BRT-B CN3 CN1 CONTROL PWB Power Supply Control Signals Circuit SOURCE DRIVER LCD PANEL 1366×3(RGB)×768 BACK LIGHT(CC BACK LIGHT(CCFT×5) INVERTER ...
Page 7
SELLVDS= High (3.3V) or Open CKAIN+ CKAIN- RIN0 RIN0- RIN1 RIN1- RIN2 RIN2- RIN3 RIN3 SELLVDS= Low(GND) CKIN+ CKIN- RIN0 RIN0- RIN1 RIN1 RIN2+ RIN2- RIN3+ ...
Page 8
Normal (Default) R/L : L（GND）U/D: L（GND） ＣＮ１ Vertical reverse image R/L : L（GND）U/D : H（3.3V） ＣＮ１ 【Note 3】The equivalent circuit figure of the terminal 【Note 4】The equivalent circuit figure of the ...
Page 9
CN3 (O/S control) (Shown Fig 1) O/S Driving Pin No and function Using connector : SM07B-SRSS-TB-A (JST) Mating connector : SHR-07V-S or SHR-07V-S-B（JST） Pin No. Symbol 1 Frame Frame frequency setting 2 O/S set O/S operation setting 3 TEST Not ...
Page 10
Backlight driving CN2 (Inverter control) Using connector: S14B-PHA-SM-TB (JST) Mating connector: PHR-14 (JST) Pin No. Symbol GND BRT BRT-B 14 ...
Page 11
The back light system characteristics The back light system is direct type with 5 CCFTs (Cold Cathode Fluorescent Tube). The characteristics of the lamp are shown in the following table. The value mentioned below is at the case of ...
Page 12
Electrical Characteristics 6-1. Control circuit driving Parameter Supply voltage +12V supply Current voltage dissipation Permissible input ripple voltage Differential input High threshold voltage Low Input Low voltage Input High voltage Input leak current (Low) Input leak current (High) Terminal ...
Page 13
The explanation of RGB gray scale is seen in section ...
Page 14
Inverter driving for back light The back light system is direct type with 5 CCFTs (Cold Cathode Fluorescent Tube). Parameter Symbol Current dissipation electricity ＋24V consumption Supply voltage Permissible input ripple voltage Input voltage (Low) Input voltage (High) Brightness ...
Page 15
Timing characteristics of input signals 7-1. Timing characteristics Timing diagrams of input signal are shown in Fig.2 Parameter Clock Frequency Horizontal period Data enable Horizontal period (High) signal Vertical period Vertical period (High) 【Note】When vertical period is very long, ...
Page 16
Input data signal and display position on the screen (１､１) (１,２) １・１ １・２ １・３ ２・１ ２・２ ３・１ 768･ Display Position of Data (V,H) 1･1366 768･1366 ...
Page 17
Input Signal, Basic Display Colors and Gray Scale of Each Color Colors & Gray Gray scale Scale Black − Blue − Green − ...
Page 18
Optical characteristics Ta=25℃, Vcc = +12V +24V INV Parameter Horizontal Viewing angle range Vertical Contrast ratio Response time Chromaticity of white Chromaticity of red Chromaticity of green Chromaticity of blue Luminance of white Luminance uniformity Measurement condition ...
Page 19
The contrast ratio is defined as the following. Contrast Ratio 【Note 3】Definition of response time Response time The response time ( d and r) is defined as ...
Page 20
Display Quality The display quality of the color TFT-LCD module shall be compliance with the incoming inspection standard 11. Handling Precautions of the module a) Be sure to turn off the power supply when inserting or disconnecting the cable. ...
Page 21
When giving a touch to the panel at power on supply, it may cause some kinds of degradation. In that case, once turn off the power supply, and turn on after several seconds again, and that is disappear. o) ...
Page 22
... Others 1)Lot No. Label ; The label that displays SHARP, product model (LQ200T3LZ18), a product number and “MADE IN JAPAN” is stuck on the back of the module production year(the last figures of the Christian Era) 2) Packing Label （４Ｓ） LQ200T3LZ18 社内品番： ...
Page 23
Carton storage condition Temperature 0℃ to 40℃ Humidity 95%RH or less Reference condition : 20℃ to 35℃ , 85%RH or less (summer) : 5℃ to 15℃ , 85%RH or less (winter) Sunlight Be sure to shelter a product from ...
Page 24
...
Page 25
...