SDS5C064G0000E0 SanDisk, SDS5C064G0000E0 Datasheet
SDS5C064G0000E0
Specifications of SDS5C064G0000E0
Related parts for SDS5C064G0000E0
SDS5C064G0000E0 Summary of contents
Page 1
... SSD SATA 5000 2.5" Product Manual Preliminary, Rev 0.7 Document No. 80-11-01488 July 2008 SanDisk Corporation Corporate Headquarters • 601 McCarthy Blvd. • Milpitas, CA 95035 Phone (408) 801-1000 • Fax (408) 801-8657 www.sandisk.com ...
Page 2
... Interface ................................................................... 14 7. Supported Standards .................................................... 14 7.1 Interface Connector Characteristics ................................ 14 7.2 Hotplug Support .......................................................... 14 7.3 © 2008 SanDisk® Corporation Product Manual 2 July 2008, Document No. 80-11-01488 Rev 0.7 ...
Page 3
... Basic Checks ............................................................... 18 8.2 BIOS Setup ................................................................. 18 8.3 Slow Drive Performance ................................................ 18 8.4 Ordering Information ................................................... 19 9. © 2008 SanDisk® Corporation Product Manual 3 July 2008, Document No. 80-11-01488 Rev 0.7 ...
Page 4
... General Description 1.1 SanDisk SSD SATA 5000 2.5" is designed to drive the shift of mobile PC users and blade server users from the hard disk drive to the solid state drive (SSD). A drop-in replacement for the hard disk drive, it delivers far superior durability, performance and power efficiency ─ keeping mobile PCs and blade servers working optimally in the toughest of conditions. SanDisk SSD SATA 5000 2.5" ...
Page 5
... Commercial: 0˚C to 70˚C o Enhanced: -25˚C to 75˚C Non-operating temperature and storage: -55˚C to 95˚C o Block Diagram 1.3 Figure 1: SanDisk SSD SATA 5000 2.5” Block Diagram © 2008 SanDisk® Corporation Product Manual 5 July 2008, Document No. 80-11-01488 Rev 0.7 ...
Page 6
... SATA 1.0a Gen1i (1.5Gb/s) SATA 2.5 ATA-7 The SSD supports Serial ATA 1.5Gbps (150MB/sec) interface rate. Capacity 2.2 This datasheet refer to the 8, 16, 32, 64GB version. Table 1: SanDisk SSD SATA 5000 2.5” Capacity Unformatted Total Number of Capacity User-Addressable Sectors in LBA Mode 8GB ...
Page 7
... Parameter Maximum Read (Typical) Write (Typical) Active Idle (Typical) Idle (Typical) Standby (Typical) Sleep (Typical) Power Consumption Efficiency 3.3 Table 5: SanDisk SSD SATA 5000 2.5” Power Consumption Efficiency Capacity (GB Power consumption efficiency is calculated as Power Consumption Idle (watts)/Capacity (GB) 2. Preliminary © ...
Page 8
... SSD SATA 5000 2.5" Physical Characteristics 4. Mechanical 4.1 Table 6: SanDisk SSD SATA 5000 2.5” Mechanical Dimensions and Weight Parameter Width Height Length Maximum Weight Mounting Instructions 4.2 Before unpacking and installing the drive, take anti-static measures in order to avoid damage to the drive. The drive may be exposed to potential handling and electrostatic discharge (ESD) hazards ...
Page 9
... SSD SATA 5000 2.5" Installation Orientation 4.3 The SSD can be installed in all axes (6 directions). For a mechanical drawing, see Figure 2. Figure 2: SanDisk SSD SATA 5000 2.5” Mechanical Drawing © 2008 SanDisk® Corporation Product Manual 9 July 2008, Document No. 80-11-01488 Rev 0.7 ...
Page 10
... Maximum relative humidity gradient Vibration 5.3 Table 9: SanDisk SSD SATA 5000 2.5” Vibration Support Parameter Operating Shock 5.4 Table 10: SanDisk SSD SATA 5000 2.5” Shock Support Parameter Operating Non-operating © 2008 SanDisk® Corporation Product Manual Specifications 0°C to 70°C -25° ...
Page 11
... SSD SATA 5000 2.5" Altitude 5.5 Table 11: SanDisk SSD SATA 5000 2.5” Altitude Support Parameter Operating Non-operating Acoustics 5.6 The SSD does not generate any acoustic noise (0dB). Regulations 5.7 The SSD is certified with the following standards. Table 12: SanDisk SSD SATA 5000 2.5” Regulation Standards ...
Page 12
... SSD SATA 5000 2.5" EMC 5.7.1 Directive 73/23/ECC for product safety Directive 89/336/EEC: Table 13: SanDisk SSD SATA 5000 2.5” Electromagnetic Compatibility Parameter Emission Immunity FCC 5.7.2 FCC 47CFR part 15 subpart B class B. RoHS 5.8 Directive of the European Parliament and of the Council on the Restriction of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment, 2002/95/EC, January 2003 ...
Page 13
... Mean Time to Failure 6.3 Mean Time to failure (MTTF) is calculated based on part stress analysis. The following conditions are set for calculation: Ambient temperature = 25°C Table 14: SanDisk SSD SATA 5000 2.5” MTTF Capacity (GB) 8, 16, 32, 64 Preventive Maintenance 6.4 No preventive maintenance is required. ...
Page 14
... The SSD complies with the following standards: ATA/ATAPI-7: ANSI INCITS 397-2005, AT Attachment with Packet Interface-7. Serial ATA Revision 2.5 Specification (Ratification Date: October 27, 2005). Interface Connector Characteristics 7.2 Table 15: SanDisk SSD SATA 5000 2.5” Connector Characteristics Parameter Drive Connector Mating/Unmating force Durability Hotplug Support 7.3 The SSD supports hotplug operation per SATA 2 ...
Page 15
... SSD SATA 5000 2.5" Pin Assignment 7.6 Table 16: SanDisk SSD SATA 5000 2.5” Pin Assignment Pin Function S1 Ground Ground Ground Ground P5 Ground P6 Ground P10 Ground P11 DAS P12 Ground P13 V 12 P14 V 12 P15 V 12 All pins are in a single row, with a 1.27 mm (0.050”) pitch. ...
Page 16
... Enable write cache (default: On) sub-commands: Set transfer mode Enable Advanced Power Management Enable SATA Feature - software Setting Preservation Enable automatic acoustic management Disable look-ahead Disable reverting to power-on defaults © 2008 SanDisk® Corporation Product Manual Command Code 92h 90h E7h EAh ECh ...
Page 17
... Security Erase Unit Security Freeze Lock Security Set Password Security Unlock ATA standard power management commands Check Power Mode Idle Idle Immediate Sleep Standby Standby Immediate © 2008 SanDisk® Corporation Product Manual 82h 85h 90h AAh C2h CCh B0h/D0h B0h/D1h B0h /D2h ...
Page 18
... Verify that the disk is enabled in the BIOS. In most new BIOSs, there is an option for drive auto-identification. Slow Drive Performance 8.4 Poor disk performance may be due to one of the following: Check that Write Caching is enabled in the drive under the category Properties. © 2008 SanDisk® Corporation Product Manual 18 July 2008, Document No. 80-11-01488 Rev 0.7 ...
Page 19
... SSD SATA 5000 2.5" Ordering Information 9. Table 17: SanDisk SSD SATA 5000 2.5” Ordering Information SD SanDisk I Interface: S – SATA G Generation: 5 – 5000 ( Form factor: C – 2.5" (9.5mm) CCC Capacity (GB): 008 016 032 064 U Units: G (GB) XXXX Customer code reference Component generation G 0 – ...
Page 20
... Corporation general policy does not recommend the use of its products in life support applications where in a failure or malfunction of the product may directly threaten life or injury. Per SanDisk Terms and Conditions of Sale, the user of SanDisk products in life support applications assumes all risk of such use and indemnifies SanDisk against all damages. See “ ...