66507-2 TE Connectivity, 66507-2 Datasheet - Page 4

• Manufacturer Part Number: 66507-2
• Description: PIN CONTACT,20DF
• Manufacturer: TE Connectivity

Specifications of 66507-2

• Rohs Compliant: YES
• Product Type: Contact
• Product Series: HDP-20 (Crimp Snap)
• Termination Method To Wire/cable: Crimp
• Wire Insulation Diameter (mm [in]): 0.76 – 1.02 [0.030 – 0.040]
• Insulation Support: Yes
• Grade: Standard
• Contact Retention In Housing: Crimp Snap-In
• Solder Tail Contact Plating: Gold (50)
• Pin Diameter (mm [in]): 1.02 [0.040]
• Wire Range (mm² [awg]): 0.08 - 0.20 [28-24]
• Used With: AMPLIMITE HDP-20
• Contact Type: Pin
• Contact Base Material: Brass
• Contact Plating, Mating Area, Material: Gold (50)
• Contact Size: 20
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Packaging Method: Strip

Contact retention force.
Contact engaging force.
Contact separating force.
Crim p tensile.
Therm al shock.
Hum idity/tem perature cycling.
Tem perature life.
Mixed flowing gas.
Rev F
NOTE
Test Description
Shall meet visual requirements, show no physical damage, and meet requirements of additional
tests as specified in the Product Qualification and Requalification Test Sequence shown in Figure
2.
Contacts shall nor dislodge from
housing when subjected to a
m inim um force of 44.5 N [10 lbf].
2.2 N [8 ozf] m axim um per contact. EIA-364-37.
0.208 N [.75 ozf] m inim um per
contact.
See Note.
See Note.
See Note.
See Note.
W ire Size
(AW G)
18
20
22
24
26
28
ENVIRONMENTAL
Figure 1 (end)
Requirem ent
(N [lbf] m inim um )
Crim p Tensile
120.1 [27]
89 [20]
53.4 [12]
35.6 [8]
20 [4.5]
12 [2.7]
EIA-364-29.
Apply specified to contacts in an
axial direction and hold for 6
seconds.
Measure force necessary to insert
gage A to a depth of 5.6 m m [.220
in].
See Figure 6.
EIA-364-37.
Size 2 tim es using gage A. Insert
gage B to a depth of 5.6 m m [.220
in] and m easure force necessary to
separate gage B.
See Figure 6.
EIA-364-8.
Determ ine crim p tensile at a
m axim um rate of 25.4 m m [1 in] per
m inute.
EIA-364-32, Test Condition VII.
Subject unm ated specim ens to 5
cycles between -55 and 105°C.
EIA-364-31, Method III with cold
shock.
Subject m ated specim ens to 10
cycles (10 days) between 25 and
65°C at 80 to 100% RH.
EIA-364-17, Method A, Test
Condition 4, Test Tim e Condition C.
Subject m ated specim ens to 105°C
for 500 hours.
EIA-364-65, Class IIIA (4 gas).
Subject m ated specim ens to
environm ental Class IIIA for 20
days.
Procedure
108-40005
4 of 10