AD7688BRMZ Analog Devices Inc, AD7688BRMZ Datasheet - Page 16

• Manufacturer Part Number: AD7688BRMZ
• Description: IC ADC DIFF 16BIT 500KSPS 10MSOP
• Manufacturer: Analog Devices Inc
• Series: PulSAR®r

Specifications of AD7688BRMZ

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Bits: 16
• Sampling Rate (per Second): 500k
• Number Of Converters: 1
• Power Dissipation (max): 21.5mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 10-TFSOP (0.118", 3.00mm Width)
• Resolution (bits): 16bit
• Sampling Rate: 500kSPS
• Input Channel Type: Differential
• Supply Voltage Range - Analog: 4.5V To 5.5V
• Supply Current: 1nA
• Digital Ic Case Style: SOP
• Number Of Elements: 1
• Resolution: 16Bit
• Architecture: SAR
• Sample Rate: 500KSPS
• Input Polarity: Bipolar
• Input Type: Voltage
• Rated Input Volt: ±5V
• Differential Input: Yes
• Power Supply Requirement: Single
• Single Supply Voltage (typ): 5V
• Single Supply Voltage (min): 4.5V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 21.5mW
• Differential Linearity Error: ±1LSB
• Integral Nonlinearity Error: ±1.5LSB
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 10
• Package Type: MSOP
• Input Signal Type: Differential
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7688CB - BOARD EVALUATION FOR AD7688
• Lead Free Status / Rohs Status: Compliant

AD7688
variations over a wide frequency range, as shown in Figure 31,
which represents PSRR over frequency.
The AD7688 powers down automatically at the end of each
conversion phase and, therefore, the power scales linearly with
the sampling rate, as shown in Figure 32. This makes the part
ideal for low sampling rate (even a few Hz) and low battery-
powered applications.
SUPPLYING THE ADC FROM THE REFERENCE
For simplified applications, the AD7688, with its low operating
current, can be supplied directly using the reference circuit
shown in Figure 33. The reference line can be driven by either:
•
•
•
0.001
1000
The system power supply directly.
A reference voltage with enough current output capability,
such as the ADR43x.
A reference buffer, such as the AD8031, which can also
filter the system power supply, as shown in Figure 33.
0.1
95
90
85
80
75
70
65
60
10
1
10
Figure 32. Operating Currents vs. Sampling Rate
100
Figure 31. PSRR vs. Frequency
10
SAMPLING RATE (SPS)
FREQUENCY (kHz)
1000
100
10000
VDD
VIO
1000
100000
1000000
10000
Rev 0 | Page 16 of 28
DIGITAL INTERFACE
Though the AD7688 has a reduced number of pins, it offers
flexibility in its serial interface modes.
The AD7688, when in CS mode, is compatible with SPI, QSPI,
digital hosts, and DSPs, e.g., Blackfin® ADSP-BF53x or ADSP-
219x. This interface can use either 3-wire or 4-wire. A 3-wire
interface using the CNV, SCK, and SDO signals minimizes
wiring connections useful, for instance, in isolated applications.
A 4-wire interface using the SDI, CNV, SCK, and SDO signals
allows CNV, which initiates the conversions, to be independent
of the readback timing (SDI). This is useful in low jitter
sampling or simultaneous sampling applications.
The AD7688, when in chain mode, provides a daisy chain
feature using the SDI input for cascading multiple ADCs on a
single data line similar to a shift register.
The mode in which the part operates depends on the SDI level
when the CNV rising edge occurs. The CS mode is selected if
SDI is high and the chain mode is selected if SDI is low. The
SDI hold time is such that when SDI and CNV are connected
together, the chain mode is always selected.
In either mode, the AD7688 offers the flexibility to optionally
force a start bit in front of the data bits. This start bit can be
used as a BUSY signal indicator to interrupt the digital host and
trigger the data reading. Otherwise, without a BUSY indicator,
the user must time out the maximum conversion time prior to
readback.
The BUSY indicator feature is enabled as:
• In the CS mode, if CNV or SDI is low when the ADC
• In the chain mode, if SCK is high during the CNV rising edge
1
5V
OPTIONAL REFERENCE BUFFER AND FILTER.
conversion ends (Figure 37 and Figure 41).
(Figure 45).
10kΩ
1µF
Figure 33. Example of Application Circuit
5V
AD8031
1
10µF
5V
REF
10Ω
AD7688
VDD
1µF
VIO