MCP3301-CI/P Microchip Technology, MCP3301-CI/P Datasheet - Page 3

• Manufacturer Part Number: MCP3301-CI/P
• Description: IC ADC 13BIT 2.7V 1CH SPI 8-DIP
• Manufacturer: Microchip Technology

Specifications of MCP3301-CI/P

• Package / Case: 8-DIP (0.300", 7.62mm)
• Number Of Bits: 13
• Sampling Rate (per Second): 100k
• Data Interface: Serial, SPI™
• Number Of Converters: 1
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Through Hole
• Architecture: SAR
• Conversion Rate: 100 KSPs
• Resolution: 12 bit
• Input Type: Voltage
• Snr: 80.02 dB
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Input Signal Type: Pseudo-Differential, Differential
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: TMPSNS-RTD1 - BOARD EVAL PT100 RTD TEMP SENSOR
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: MCP3301CI/P

1.0
Maximum Ratings*
V
All inputs and outputs w.r.t. V
Storage temperature .......................... -65°C to +150°C
Ambient temp. with power applied ..... -65°C to +125°C
Maximum Junction Temperature ....................... 150°C
ESD protection on all pins (HBM)......................... > 4 kV
*Notice: Stresses above those listed under “Maximum rat-
ings” may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at
those or any other conditions above those indicated in the
operational listings of this specification is not implied. Expo-
sure to maximum rating conditions for extended periods may
affect device reliability.
ELECTRICAL SPECIFICATIONS
© 2007 Microchip Technology Inc.
Electrical Characteristics: Unless otherwise noted, all parameters apply at V
configuration (Figure 3-4) with fixed common mode voltage of 2.5V. All parameters apply over temperature with
T
Conversion Rate
Maximum Sampling Frequency
Conversion Time
Acquisition Time
DC Accuracy
Resolution
Integral Nonlinearity
Differential Nonlinearity
Positive Gain Error
Negative Gain Error
Offset Error
Dynamic Performance
Total Harmonic Distortion
Signal to Noise and Distortion
Spurious Free Dynamic Range
Common-Mode Rejection
Power Supply Rejection
Note 1: This specification is established by characterization and not 100% tested.
DD
AMB
........................................................................ 7.0V
= -40°C to +85°C (Note 7). Conversion speed (f
2: See characterization graphs that relate converter performance to V
3: V
4: V
5: Maximum clock frequency specification must be met.
6: V
7: MSOP devices are only specified at 25°C and +85°C.
8: For slow sample rates, see Section 6.2.1 for limitations on clock frequency.
ELECTRICAL
CHARACTERISTICS
IN
DD
REF
Parameter
= 0.1V to 4.9V @ 1 kHz.
= 5VDC ±500 mV
= 400 mV, V
IN
= 0.1V to 4.9V @ 1 kHz
SS
P
.......-0.3V to V
-
P
@ 1 kHz, see test circuit Figure 3-3.
Symbol
f
SAMPLE
SINAD
CMRR
SFDR
t
PSR
CONV
t
DNL
THD
INL
ACQ
DD
SAMPLE)
+0.3V
Min
—
—
—
—
—
—
—
—
—
-3
-3
-3
—
12 data bits + sign
is 100 ksps with f
-0.75
±0.5
±0.5
Typ
-0.5
-91
±1
+3
78
92
79
74
—
—
1.5
13
PIN FUNCTION TABLE
V
IN(+)
IN(-)
V
CS/SHDN
D
CLK
V
REF
SS
DD
OUT
Name
Max
100
50
±1
±2
±1
+2
+2
+6
—
—
—
—
—
DD
REF
CLK
= 5V, V
level.
= 17*f
periods
periods
Reference Voltage Input
Positive Analog Input
Negative Analog Input
Ground
Chip Select / Shutdown Input
Serial Data Out
Serial Clock
+2.7V to 5.5V Power Supply
Units
ksps
ksps
CLK
CLK
LSB
LSB
LSB
LSB
LSB
SS
bits
SAMPLE
dB
dB
dB
dB
dB
= 0V, and V
Note 8
V
MCP3301-B
MCP3301-C
Monotonic with no missing codes
over temperature
Note 3
Note 3
Note 3
Note 6
Note 4
DD
= V
REF
Function
REF
MCP3301
= 5V. Full differential input
Conditions
= 2.7V, V
DS21700C-page 3
CM
=1.35V