MK5811S IDT, Integrated Device Technology Inc, MK5811S Datasheet - Page 3

• Manufacturer Part Number: MK5811S
• Description: IC CLK GENERATOR LOW EMI 8-SOIC
• Manufacturer: IDT, Integrated Device Technology Inc
• Type: Clock Generatorr

Specifications of MK5811S

• Pll: Yes
• Input: Clock, Crystal
• Output: LVCMOS
• Number Of Circuits: 1
• Ratio - Input:output: 1:1
• Differential - Input:output: No/No
• Frequency - Max: 32MHz
• Divider/multiplier: No/Yes
• Voltage - Supply: 3 V ~ 3.63 V
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC
• Frequency-max: 32MHz
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Pin Descriptions
External Components
The MK5811 requires a minimum number of external
components for proper operation.
Decoupling Capacitor
A decoupling capacitor of 0.01µF must be connected
between VDD and GND on pins 7 and 2. Connect the
capacitor as close to these pins as possible. For optimum
device performance, mount the decoupling capacitor on the
component side of the PCB. Avoid the use of vias in the
decoupling circuit.
Series Termination Resistor
Use series termination when the PCB trace between the
clock output and the load is over 1 inch. To series terminate
a 50 trace (a commonly used trace impedance), place a
33 resistor in series with the clock line. Place the resistor
as close to the clock output pin as possible. The nominal
impedance of the clock output is 20 .
Tri-level Select Pin Operation
The S1 and S0 select pins are tri-level, meaning that they
have three separate states to make the selections shown in
the table on page 2. To select the M (mid) level, the
connection to these pins must be eliminated by either
floating them originally, or tri-stating the GPIO pins which
drive the select pins.
IDT™ / ICS™ LOW EMI CLOCK GENERATOR
MK5811
LOW EMI CLOCK GENERATOR
Number
Pin
1
2
3
4
5
6
7
8
X1/ICLK
SSCLK
FRSEL
Name
GND
VDD
Pin
S1
S0
X2
Pin Type
Output
Power
Power
Input
Input
Input
Input
XO
Connect to 4-32 MHz crystal or clock.
Connect to ground.
Function select 1 input. Selects spread amount and direction per table above.
(default-internal mid-level).
Function select 0 input. Selects spread amount and direction per table above.
(default-internal mid-level).
Clock output with Spread spectrum
Function select for input frequency range. Default to mid level “M”.
Connect to +3.3 V.
Crystal connection to 4-32 MHz crystal. Leave unconnected for clock
3
PCB Layout Recommendations
For optimum device performance and lowest output phase
noise, observe the following guidelines:
1) Mount the 0.01µF decoupling capacitor on the
component side of the board as close to the VDD pin as
possible. No vias should be used between the decoupling
capacitor and VDD pin. The PCB trace to the VDD pin and
the PCB trace to the ground via should be kept as short as
possible.
2) To minimize EMI, place the 33 series-termination
resistor (if needed) close to the clock output.
3) An optimum layout is one with all components on the
same side of the board, thus minimizing vias through other
signal layers. Other signal traces should be routed away
from the MK5811 device. This includes signal traces located
underneath the device, or on layers adjacent to the ground
plane layer used by the device.
Crystal Information
The crystal used should be a fundamental mode (do not use
third overtone), parallel resonant crystal. To optimize the
initial accuracy, connect crystal capacitors from pins X1 to
ground and X2 to ground. The value of these capacitors is
given by the following equation:
Crystal caps (pF) = (C
Pin Description
L
- 6) x 2
MK5811
REV F 051310
SSCG